Honeywell Sensepoint XCD RTD Скачать руководство пользователя страница 6

Страница: 6 / 68

Sensepoint XCD RTD Technical Manual SPXCDHMRTEN Issue 1

Locking

Grub

screw

Sensepoint Toxic

Internal Earth

Point

Enclosure

External Earth

Point (x2)

M20 Field Cable Entries

(x2)

Cover

Seal

Display Module

Terminal Module

M25 entry

EExd Plug

Integral

mounting plate

Certification Label

4 Introduction

The Sensepoint XCD RTD comprises a gas detector transmitter and a choice of sensors

for detecting toxic gas and oxygen. The construction of Sensepoint XCD allows it to be

used in hazardous area locations; it may also be used in other areas not classified as

hazardous.

There are three different versions of Sensepoint XCD, The RTD version is used with

Sensepoint Toxic sensors that can be locally or remotely mounted. The detectable gases

for Sensepoint XCD RTD include Ammonia, Chlorine, Nitrogen, Monoxide, Nitrogen

Dioxide, Sulphur Dioxide,Oxygen, Hydrogen Sulphide,Carbon Monoxide and Hydrogen.

The transmitter features a display and three programmable relays for controlling external

equipment e.g. alarms, sirens, valves or switches. The transmitter provides an industry

standard 3-wire, 4-20mA source or sink output for connection to a dedicated gas detection

control system or PLC.

Configuration and Maintenance is carried out using a Magnetic Wand, this allows a single

user to undertake routine maintenance without needing to access internal components.

Sensepoint XCD RTD is suitable for use in Zone 1 or 2 hazardous areas.

Sensepoint XCD RTD comprises of the main parts as shown below.

Diagram 1. – Exploded View

Содержание Sensepoint XCD RTD





































































Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RTD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды