Honeywell Sensepoint XCD RTD Скачать руководство пользователя страница 40

Страница: 40 / 68

Sensepoint XCD RTD Technical Manual SPXCDHMRTEN Issue 1

13 Menu’s and Advanced Configuration

13.1 Abort Function

In Review Mode or Configuration Mode the user can escape one step back from the

current position using the Abort Function. To do this the user must activate the Enter

switch for more than 3 seconds with the Magnetic Wand. Switching between each pair of

modes or between menus and sub menus are shown in the following table.

From

Example

Review Mode

Monitoring Mode

Activate Enter switch for more than 3 seconds

while in Review Mode

Configuration Mode

Monitoring Mode

Activate Enter switch for more than 3 seconds

while navigating menus in the Configuration

Mode

Configuration Mode

sub menu

Configuration

Mode main menu

Activate Enter switch for more than 3 seconds

while in a sub menu

Table 8: Transmitter menu switching

13.2 Configuration Mode

The table below shows the functions available via the configuration menu that can be

displayed on the transmitter and accessed using the Magnetic Wand.

The instrument will show the main Menu when the “Enter” switch is activated with the

Magnetic Wand and held for at least 3 seconds.

The Menu is password protected to prevent any unauthorized changes. The password is

initially disabled and the default password is ‘0000’. If the default password is changed

to other than ‘0000’, then the password is enabled automatically and requested when

entering Configuration Mode.

With the Menu showing, the following functions can be performed: calibration, bump test,

sensor selection and configuration of parameters such as measuring range, calibration

gas level, calibration interval, inhibit current, inhibit timeout, alarm setting, relay setting,

password change, location setting, temperature unit reading, force analogue output and

alarm function checks.

While in Configuration mode, the output current of the transmitter is inhibited to prevent

false alarms.

Names, displays and descriptions for each menu item in Configuration Mode are shown in

the following table.

Содержание Sensepoint XCD RTD





































































Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RTD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды