Honeywell RM7838B Series Скачать руководство пользователя страница 53

Страница: 53 / 56

65-0120—1

RM7838B

TROUBLESHOOTING

TABLE 14—EXPANDED ANNUNCIATOR FAULT CODES (Continued)

Annunciation Message

Symbol

System Faults

LOCKOUT nnh
*High Oil Pres.*

Oil pressure was above high oil pressure limit.

LOCKOUT nni
*Low Oil Pres.*

Oil pressure was below low oil pressure limit.

LOCKOUT nnj
*High Oil Temp.*

Oil temperature was above high oil temperature limit.

LOCKOUT nnk
*Low Oil Temp.*

Oil temperature was below low oil temperature limit.

LOCKOUT nnm
*Atomizing Sw.*

Atomizing switch failed to close.

LOCKOUT nnn
*High Gas Pres.*

Gas pressure was above high gas pressure limit.

LOCKOUT nno
*Low Gas Pres.*

Gas pressure was below low gas pressure limit.

LOCKOUT nnp
*Airflow Switch*

The Airflow Switch was open when it should have been closed
or vice versa.

LOCKOUT nnq
*Aux. ILK #4*

Auxiliary Interlock #3 was open.

LOCKOUT nnr
*Aux. ILK #5*

Auxiliary Interlock #4 was open.

LOCKOUT nns
*Other ILKs*

Other Auxiliary Interlocks were open.

LOCKOUT nny
*Valve Closure*

Preignition Interlock or other valve closure switch was open.

LOCKOUT nnz
*Other PIIs*

Other Preignition Interlocks were open.

EXPANDED ANNUNCIATOR DIAGNOSTIC
CURRENT STATUS MESSAGES (TABLE 15)

These message are used to provide information from the

Expanded Annunciator to the Keyboard Display Module in
Current Status EA Diagnostics, see Table 5. This informa-
tion explains the first limit or interlock that is de-energized in
the system.

TABLE 15—EXPANDED ANNUNCIATOR

DIAGNOSTIC CURRENT STATUS MESSAGES.

Display

Description

Burner Sw.

Burner Switch

Oper. Control

Operating Control

Aux. Limit #1

Auxiliary Limit #1

Aux. Limit #2

Auxiliary Limit #2

LWCO

Low Water Cutoff

High Limit

High Temperature or
High Pressure Limit

Aux. Limit #3

Auxiliary Limit #3

FuelSelectOff

Fuel Select Off

BothFuelSelect

Both Fuels Selected

High Oil Pres.

High Oil Pressure

Low Oil Pres.

Low Oil Pressure

High Oil Temp.

High Oil Temperature

Low Oil Temp.

Low Oil Temperature

Atomizing Sw.

Atomizing Switch

High Gas Pres.

High Gas Pressure

Low Gas Pres.

Low Gas Pressure

Airflow Sw.

Airflow Switch

Aux. ILK #4

Auxiliary Interlock #4

Aux. ILK #5

Auxiliary Interlock #5

All switches on

Содержание RM7838B Series

























































Результаты поиска

Содержание RM7838B Series

Отзывы:

Honeywell RM7838B Series, Руководство пользователя, Страница: 53 / 56

Результаты поиска

Содержание RM7838B Series

Отзывы: