Honeywell RM7838B Series Скачать руководство пользователя страница 52

Страница: 52 / 56

65-0120—1

TABLE 13—EXPANDED ANNUNCIATOR HOLD CODES.

Annunciation Message

Symbol

System Holds

BURNER OFF: T6
(Burner Switch)

Burner switch is open.

STANDBY HOLD: T6
(Aux. Limit #1)

Auxiliary limit #1 is open.

STANDBY HOLD: T6
(Aux. Limit #2)

Auxiliary limit #2 is open.

STANDBY HOLD: T6
(LWCO)

Open low water cutoff.

STANDBY HOLD: T6
(High Limit)

High limit (pressure or temperature) exceeded.

STANDBY HOLD: T6
(Aux. Limit #3)

Auxiliary limit #3 is open.

STANDBY HOLD: T6
(FuelSelect Off)

No fuel selected.

STANDBY HOLD: T6
(BothFuelSelect)

Both fuels selected.

STANDBY HOLD: T6
(High Oil Pres.)

Oil pressure is above high oil pressure limit.

STANDBY HOLD: T6
(Low Oil Pres.)

Oil pressure is below low oil pressure limit.

STANDBY HOLD: T6
(High Oil Temp.)

Oil temperature is above high oil temperature limit.

STANDBY HOLD: T6
(Low Oil Temp.)

Oil temperature is below low oil temperature limit.

STANDBY HOLD: T6
(Atomizing Sw.)

Atomizing Switch is open.

STANDBY HOLD: T6
(High Gas Pres.)

Gas pressure is above high gas pressure limit.

STANDBY HOLD: T6
(Low Gas Pres.)

Gas pressure is below low gas pressure limit.

STANDBY HOLD: T6
(Circuit Fault)

Control input is not energized.

TABLE 14—EXPANDED ANNUNCIATOR FAULT CODES.

Annunciation Message

Symbol

System Faults

LOCKOUT nna
*Aux. Limit #1*

Auxiliary limit #1 was open.

LOCKOUT nnb
*Aux. Limit #2*

Auxiliary limit #2 was open.

LOCKOUT nnc
*LWCO*

Open low water cutoff.

LOCKOUT nnd
*High Limit*

High limit (pressure or temperature) was exceeded.

LOCKOUT nne
*Aux. Limit #3*

Auxiliary limit #3 was open.

LOCKOUT nnf
*FuelSelect Off*

No fuel selected.

LOCKOUT nng
*BothFuelSelect*

Both fuels selected.

(continued)

RM7838B

TROUBLESHOOTING

Содержание RM7838B Series

























































Результаты поиска

Содержание RM7838B Series

Отзывы:

Honeywell RM7838B Series, Руководство пользователя, Страница: 52 / 56

Результаты поиска

Содержание RM7838B Series

Отзывы: