Honeywell RM7838B Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 56

Honeywell RM7838B Series Скачать руководство пользователя страница 47

47

65-0120—1

TABLE 11—SELECTABLE MESSAGES (SEE TABLE 4) (Continued)

Selectable Message/

Possible States/Range

Display

Description

(Terminals)

Comments

Ignition

T10

Ignition.

ON or OFF

Indicates if output term-
inal is on (energized) or
off (de-energized.)

PV Hold

T16

Pilot Valve Hold

ON or OFF

Indicates if RM7838B
is commanded to hold
in Pilot.

ManOpenSw

T17

Manual Open Valve

ON or OFF

Indicates if Valve is at

Switch

open position.

LowFire Sw

T18

Low Fire Switch.

ON or OFF

Indicates if input is on
(energized) or off
(de-energized.)

HighFireSw

T19

High Purge Rate Switch.

ON or OFF

Indicates if input is
(energized) or off
(de-energized.)

PreIgn ILK

T20

Preignition Interlock.

ON or OFF

Indicates if input is on
(energized) or off
(de-energized.)

V2/Start

T21

Start Switch Input.

ON or OFF

Indicates if Start Input is
present. This is momen-
tary input so RM7838B
could be in RUN and this
will read OFF.

Jumper 1

Pilot Flame

INTACT/

Display shows state of

Establishing Period

CLIPPED

PFEP jumper. If jumper is

(PFEP).

intact, the RM7838B will
have a 10 second PFEP;
if jumper is clipped,
RM7838B will have
4 second PFEP.

Jumper 2

Pilot Valve.

INTACT/

Display shows state of

CLIPPED

Pilot Valve . If jumper is
intact, RM7838B will
have Intermittent Pilot
Valve. If jumper is clipped,
RM7838B will have a
10 second Interrupted
Pilot Valve.

Jumper 3

Immediate or deferred

INTACT Deferred/

Display shows state of

MFEP.

CLIPPED Immed.

Main Fuel Valve jumper.
If jumper is clipped,
RM7838B sequences
automatically to MFEP.
If jumper is intact,
MFEP is delayed until
Manual Open Valve
input is received.

Amp Type

Defines type

NORMAL/AMP-

Display shows type of

of amplifier installed.

CHECK/SHUTTER

flame detection system
installed (i.e., NORMAL/
Standard, AMP-CHECK/
AMPLI-CHECK™, and
SHUTTER/Dynamic
Self-Checking).

RM7838B

TROUBLESHOOTING

(continued)

«
...
45
46
47
48
49
...
»

Содержание RM7838B Series

























































Отзывы:

Нет отзывов