Honeywell Galaxy Flex Скачать руководство пользователя страница 91

Страница: 91 / 246

Galaxy Flex Installer Manual

Program Zones [52]

Note:

This attribute only works when the

Chime [15]

option is enabled.

4=Omit

Enable the Omit attribute to allow these zone omit functions to be programmed,

11=OMIT

ZONES

46=GROUP OMIT

The Omit attribute defaults to 0 (disabled) for all zone functions.

Use

to toggle the status of the Omit attribute, and then press

ent

to accept the

programming.

5=Part

Disable the Part attribute to ensure the zone is excluded from the setting procedure when the
part setting options is used to set the system:

13=PART SET

. The Part attribute defaults to

1 (enabled) for all zone functions except zones programmed as

09=Keyswitch

Use

to toggle the status of the Part attribute, and then press

ent

to accept the

programming.

6=Resp. Time

This function is only applicable to zones on RIO rev 1.2 and Smart PSU rev 0.7 and above.

Use this option to select either Fast (10 ms), System (default value programmed in

Parameters [51]

, option 27) or Slow (750 ms), for each zone.

Содержание Galaxy Flex























































































































































































































































Результаты поиска

Содержание Galaxy Flex

Отзывы:

Honeywell Galaxy Flex, Руководство по установке, Страница: 91 / 246

Результаты поиска

Содержание Galaxy Flex

Отзывы: