manualshive.com logo in svg

Honeywell Galaxy Flex, Руководство по установке, Страница: 149 / 246

Поделиться
Скачать
Honeywell Galaxy Flex Скачать руководство пользователя страница 149

Galaxy Flex Installer Manual 

Communications [56]

 

 

149 

SIA Control [56.4.08] 

When using the SIA control command protocol for integration purposes, enter the IP address 
of the computer sending the SIA control commands to ensure that only commands from a 
computer with the programmed IP address are recognised by the Ethernet module. 

Enter the IP address in the form XXX.XXX.XXX.XXX. The dot separator is added 
automatically after each sequence of three numbers. To add the separator manually press 

. 

Encrypt [56.4.09] 

The Ethernet module supports 128 bit encryption for all communication options. Use this 
option to enable and disable encryption for each communication option. The default setting 
is OFF for each option. 

1=Alarm Report

 

Controls encryption for the Primary and Secondary alarm 
transmission paths. 

2=Remote Access

 

Controls encryption for the Remote Servicing sessions. 

3=SIA Control

 

Controls encryption for communications between the Ethernet 
module and remote computer using the SIA control command 
protocol. 

4=Alarm Mon.

 

Controls encryption for the Alarm Monitoring alarm transmission 
paths. 

GPRS Network [56.4.10] 

To enable GPRS operation you need to setup 

Format [56.4.02.1]

, 

Primary IP [56.4.02.2]

, 

and 

Account No.

 

[56.4.02.4]

 as well as the following options: 

1=APN

 

The Access Point Name for the GPRS provider; a maximum of 30 
characters. 

2=Login

 

The login (username) for the GPRS provider; a maximum of 20 characters. 

3=Password

  The password for the GPRS provider; a maximum of 20 characters. 

GSM [56.5] 

The GSM module has the same menu structure and function as the 

Internal Telecoms 

[56.1]

 with the following exception: 

11=Fail to Comm 

This is controlled by the number of attempts and not time. 

Line Fail [56.5.10] 
1=Network Fail 

(default 

Disabled

) A line fail occurs if a network failure is detected. The 

signal strength should be above 30% for reliability. Check this in the diagnostic menu 
61.1.06. 
 

SMS [56.5.17] 

Use this option to generate and transmit SMS text messages in response to events that occur. 

1=Mobile No.(s) 

Press 

ent 

to access and enter up to three mobile numbers (22 digits 

Содержание Galaxy Flex























































































































































































































































Отзывы:

Нет отзывов