manualshive.com logo in svg

Honeywell Galaxy Flex, Руководство по установке, Страница: 139 / 246

Поделиться
Скачать
Honeywell Galaxy Flex Скачать руководство пользователя страница 139

Galaxy Flex Installer Manual 

Communications [56]

 

 

139 

3=Snatch if Fail 

A hardware snatch is attempted if the software snatch fails or the 
software snatch is disabled. 

2=Software 

The ISDN module monitors every communication on the ISDN bus including those of other 
devices. The software snatch can clear a B-channel when both are in use. The call that 
started first is the one that is cleared. 

Certain ISDN devices do not release the B-channel when a software snatch is attempted. 
However, a hardware snatch can be attempted instead (see the 

Hardware snatch [56.3.04.1]

 

option). Software snatch can be enabled or disabled. 

ISDN Autotest [56.3.05] 

See 

Int Telecom Autotest [56.1.07]

 for details. 

ISDN Engineer Test [56.3.06] 

See 

Engineer Test [56.1.08]

 for details. 

ISDN Line Fail [56.03.07] 

The module continually monitors the ISDN line. In addition to DC volts monitoring, the 
module can be programmed to use layer 1 check monitoring. The layer 1 option activates the 
ISDN line every 40 seconds and monitors the activation response from the ISDN network. 
This activation remains for about 20 seconds. When X.25 is used the layer 1 check is not 
performed because the ISDN line is already activated continuously. 

The module can be configured using these options: 

1=None 

No line monitoring. 

2=Line Volts 

D.C. volts monitored only. 

3=Layer 1 

Layer 1 monitored only. 

4=Volts and Layer 1 

Volts and layer 1 both monitored. Line Fail activated if both fail. 

5=Volts or Layer 1 

Volts and Layer 1 both monitored. Line Fail activated if either fail. 

Fail to Comm [56.3.08] 

Use this option to set the number of unsuccessful communication attempts before the 

COMM FAIL 

message is recorded in the event log. 

When an alarm condition or event is to be transmitted to the monitoring station, the ISDN 
module snatches the telephone line and dials the programmed telephone numbers. This 
procedure is repeated for the second telephone number if the Receiver option has been 
programmed as Dual. 

Note:

  The ISDN module communicator snatches and holds the line until a successful 

attempt has been made to the required telephone numbers or all the repeat attempts 
have been tried. 

Содержание Galaxy Flex























































































































































































































































Отзывы:

Нет отзывов