Honeywell Ademco VISTA-21iPSIA Скачать руководство пользователя

Страница: 34 / 96

*58

Expert Zone Programming Menu Mode

For quickly programming zone information, but is
recommended only for those already familiar with *56
menu mode. See Zone Programming section.

System Status Report Codes

Zone report codes are programmed using interactive

✱

58 Zone Programming modes, while system status

(non-alarm) codes and restore codes are entered in data
fields *59 - *68, *70 - *76, *89. The actual report code
digits that you enter depend upon the particular
installation, and should agree with the Central Station
office receiving the signals.

3+1 or 4+1 Standard Format:

Enter a code in the

first box:

1–9, A, B, C, D, E, or F. Enter #+10 for A (this

reports a 0 on some receivers), #+11 for B, #+12 for C,
#+13 for D, #+14 for E, #+15 for F.

An entry of

in the first box disables a report. Entering

in the second box advance to the next field.

Expanded or 4+2 Format:

Enter codes in both boxes

(first/second digits) for 1–9 or A–F, as described above.
A

in the first box disables a report. A

in the second

box eliminates the expanded message for that report.

ADEMCO Contact ID® Reporting:

Enter a digit in

the first box to enable the zone to report. Use a different
digit for each zone until you have used up available
digits. If the number of zones exceeds the number of
available digits, begin with digit 1 again. This is an
“enabling” code only and is not the actual code sent to
the Central Station office. Entries in the second boxes
are ignored. An entry of

in the first box disables the

report.

Report codes are required in fields *61, *65, *71, *72, for

UL Commercial Burglar Alarm installations.

Report codes are required in fields *60, *62, *63, *64, *70, *73,
*74, *75, *76, for UL Commercial Burglar Alarm installations and
required for Residential Fire Alarm installations.

*59

Exit Error Report Code

0 = no report; 1-F = see description above

V21iPSIA:

[1] Always enabled. Also see field *69.

After arming the system, entry/exit and interior zones
remaining open after exit delay expires cause an alarm
sound at the keypad and external sounder (keypad also
displays “EXIT ALARM”), and entry delay begins.
Disarming before the end of the entry delay stops the
alarm sounding and no message is sent to the central
station. The keypad will display “CA” (fixed-word) or
“ALARM CANCELED” (alpha display).

If the system is not disarmed before entry delay expires,
an “EXIT ALARM” message (

V21iPSIA:

also zone alarm

message) will be sent to the central station. The keypad
will display “EA” (fixed-word ) or “EXIT ALARM” (alpha
display), and alarm sounding continues until the system
is disarmed (or timeout occurs).

An Exit Alarm condition will also result if a fault occurs
in an exit or interior zone within 2 minutes following the
end of the exit delay, and an “EXIT ALARM” message
will be sent to the central station (except for

V21iPSIA

see field *69 Recent Closing report).

With Contact ID

format, the message will contain the zone number
and error code 374 (“ALARM–EXIT ERROR”).

*60

Trouble Report Code

(0 = no report; 1-F = see description above *59

Sent if a zone has a trouble condition. See UL System
Reporting Note above *59.

*61

Bypass Report Code

0 = no report; 1-F = see description above *59

Sent when a zone is manually bypassed. See UL System
Reporting Note above *59.

*62

AC Loss Report Code

0 = no report; 1-F = see description above *59

Timing of this report is random with up to a 4-hour
delay. If AC restores before the report goes out, there is
no “AC LOSS” report. See UL System Reporting Note
above *59.

*63

Low Bat Report Code

0 = no report; 1-F = see description above *59

Sent when the system’s backup battery has a low-battery
condition. See UL System Reporting Note above *59.

*64

Test Report Code

0 = no report; 1-F = see description above *59

Sent periodically to test that the communicator and
phone lines are operational. See System Reporting UL
Note above *59. Frequency of report is set in Scheduling
mode (event 11) or by the following key commands:

installer code + [#] + 0 + 0

= test report sent every 24 hrs

installer code + [#] + 0 + 1

= test report sent once per week

installer code + [#] + 0 + 2

= test report sent every 28 days

Each of these modes sets schedule 32 to the selected
repeat option; first test report sent 12 hours after
command†.

†

NOTE:

Make sure the Real-Time Clock is set to the proper

time

before