background image

 

 

 

 

FCC STATEMENT 

Note:

 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 

15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference when 
the equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiates radio frequency energy and, if not installed and used in accordance 
with the instruction manual, may cause harmful interference to radio communications.  Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user will be required to correct the interference 
at his own expense. 

 

 

FCC STATEMENT 

This device complies with Part 15 of the FCC Rules, and RSS 210 of IC.  Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, 
including interference that may cause undesired operation. 
 

 

The user shall not make any changes or modifications to the equipment unless authorized by the Installation 
Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the 
equipment. 
 

 
 

 
 

 

 

DOCUMENTATION AND ONLINE SUPPORT 

For the latest documentation and online support information, please go to: 

http://www.security.honeywell.com/hsc/resources/MyWebTech/

 

WARRANTY 

For the latest warranty information, please go to: 

http://www.security.honeywell.com/hsc/resources/wa/ 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 

 

Ê800-04433V1"Š 

800-04433V1  12/10  Rev. A  

 

 

2 Corporate Center Drive, Suite 100,  

P.O. Box 9040, Melville, NY  11747 

Copyright 

 2010 Honeywell International Inc. 

www.honeywell.com/security 

 

Содержание 800-04433V1

















Отзывы: