Hobby King ORX TX10i Скачать руководство пользователя страница 23

Страница: 23 / 24

System settings

Firmware Ver.

This function shows information about the transmitter 's currently installed firmware version.

Firmware update

=Firmware ver. =

ORX Tx10i

1.0 15-Jan-2018

Hardware lJ_1.5

The function is for updating the system's firmware.

Setup:

1. Download the latest firmware from

www.hobbyking.com

2. Open the firmware update on a computer and connect the system via USB cable.

3. Select [Firmware Update] from the systems function menu. Press the wheel, the system will

show a prompt, "This will enter firmware update mode and halt other functions" with an option to
continue. Press Roller button and the screen will show "Yes" and "No". Select "Yes" and press
Roller button to confirm.

*When in update mode the system will show a prompt, "Update mode active. Turn the system off
and on again to exit".

4. Once the system has been recognized by the computer select the update button.

*Once the system has been updated it will restart.
*Once the system has restarted it is safe to remove the USB cable.

RF module ver.

=Firmware update=

This wi 11 enter

firmware update

mode and halt

other functions

Press "OK" to

confirm

This function shows information about the receiver's currently installed RF module version.

=RF module ver.

18-Apr-2018

.. •••••••••7x

ID CHANNEL TRANSMITTER

�

'"""'

DICITALPRDPDRTIDNALPRDCRAMMABLE

�I

•--=:: �

"-'

.,. �

�

RADIDCDNTADLSYSTEM

��®

Содержание ORX TX10i

























Результаты поиска

Содержание ORX TX10i

Отзывы:

Бренды по названию

Популярные бренды

Hobby King ORX TX10i, Инструкция по эксплуатации

Результаты поиска

Содержание ORX TX10i

Отзывы:

Бренды по названию

Популярные бренды