Hobby King ORX TX10i Скачать руководство пользователя

Страница: 22 / 24

Student mode

This function is used when another system is connected as a master (trainer). When this mode is

active all settings will be bypassed and the system will only function through the master.

Press and hold the wheel and move the wheel to select yes.

Sticks mode

=student mode=

This wi 11 enter

student mode

all settings

will be bypassed

Press "OK"

to confirm

There are 4 available stick modes, each stick mode changes the stick functions.

For example when using stick mode 2 the left stick controls throttle on the vertical axis and rudder

in the horizontal axis. However in stick mode 3, the vertical axis controls elevator and the horizontal
axis controls aileron. These modes are largely down to personal preference.

Move the wheel to select a stick mode then press and hold the wheel to save and exit.

LCD brightness

Sticks mode

Mode 2

Ch3=

Ch2=

Ch4,E£1 Ch!,$

This function controls the LCD backlight's brightness. Please note increasing the brightness

will reduce battery life.

To change the LCD brightness, Use the wheel to change the screen brightness then press and
hold the wheel to save and exit.

= LCD brightness=

Frame rate

This function sets the protocol type and speed. Use the wheel to highlight the desired

protocol then press and hold the wheel to save. Please note

This option is not available on

the

U version.

===Frame rate===

+Mode

DSMX

11ms

•••••••••••7x

ID CHANNEL TRANSMITTER

�

'"""'

DICITALPRDPDRTIDNAL PRDCRAMMABLE

�I

•--=:: �

"-'

.,. �

�

RADIDCDNTADL SYSTEM

��®

Содержание ORX TX10i

























Результаты поиска

Содержание ORX TX10i

Отзывы:

Похожие инструкции для ORX TX10i

Бренды по названию

Популярные бренды

Hobby King ORX TX10i, Инструкция по эксплуатации

Результаты поиска

Содержание ORX TX10i

Отзывы:

Похожие инструкции для ORX TX10i

Бренды по названию

Популярные бренды