HNP Mikrosysteme mzr-7240 Скачать руководство пользователя страница 62

Страница: 62 / 89

10 Software »Motion Manager« (Option)

Operating manual mzr-7240

Technical data subject to change without prior notice!

Last update: March 2019

Software »Motion Manager« (Option)

The »Motion Manager« software enables operation and configuration of the

drive and offers a possibility of an online graphic analysis of the operating data.

The software is delivered on CD. The program may be installed on a PC running

under Windows 7

, Windows 8 or Windows 8.1

operating systems.

Install the software »Motion Manager« by starting the program »Setup« from

the CD. If the CD are not available you may still download this program from

the web site http://www.hnp-mikrosysteme.de/download-center.html or the

web site www.faulhaber.com (menu support - download). Here, the latest

version is always available in English and German.

After the installation the »Motion Manager« program may be loaded from the

»Faulhaber Motors« folder from the Windows start menu.

In order to program the drive, the micro annular gear pump should be put into

operation. The drive should be connected to the PC with the delivered

null-modem cable.

figure 32

Software Motion Manager for motor control

To use the Motion Manager-Software please read the Online-Help.

With the following commands feeding and dosage tasks could be done.

Содержание mzr-7240


























































































Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-7240, Руководство по эксплуатации

Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды