HNP Mikrosysteme mzr-7240 Скачать руководство пользователя страница 27

Страница: 27 / 89

6 Optional motor versions

Operating manual mzr-7240

Last update: March 2019

Technical data subject to change without prior notice!

figure 14

Motor connection of control unit S-KB-4

Controller Pin

Connection motor

wire colour

Mot C

black

Mot B

red

Mot A

yellow

Controller Pin

Connection sensor

wire colour

SGND

GND

black

VCC

+5 V

red

Sens C

green

Sens B

white

Sens A

blue

table 10

Motor connection of control unit S-KB-4

mzr-pump

Mot C

Mot B

Mot A

SGND

Vcc

Sens C

Sens B

Sens A

IO1

IO2

DIR

Unsoll

GND

Umot

SC2804S 3530

speed regulation

0 - 10 V

-
+

external
voltage supply
24 VDC / 3 A

figure 15

Connection sheet of control unit S-KB-4

This manual contains general instructions that come with installing and

operating the pump. For more detailed information see the attached motion

controller instructions.

Incorrect assembly or assembly with the wrong fixing materials can cause

damage to the controllers.
Assembly and installation instructions from the manual of the motion

controller are adhere.

Electrostatic discharges at the controller connections can cause damage to or

destruction of the electronics.
Note and follow the ESD protective measures from the manual of the motion

controller are adhere.

Содержание mzr-7240


























































































Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-7240, Руководство по эксплуатации

Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды