HNP Mikrosysteme mzr-7240 Скачать руководство пользователя страница 19

Страница: 19 / 89

5 Modular system

Operating manual mzr-7240

Last update: March 2019

Technical data subject to change without prior notice!

Modular system

The spectrum of applications of the modular modular series may be expanded

by using different additional modules. The modules allow for special

applications, which could otherwise not be accomplished with a standard

pump version. The modules may be combined with each other and with almost

all available pump heads and motor versions.

−

Fluidic seal module

prevents possible chemical reactions between the

delivered liquid and the surrounding environment

−

Axial bearing module

enables the pump liquids with increased pressure

−

Gear box module

increases the torque of the drive allowing to deliver high

viscosity liquids and provides for a constant operation of the motor at low

speeds.

The configuration of a given pump version should in each case be discussed

with consideration to the specific requirements of the application.

Additional

customized modules may be designed on demand.

Содержание mzr-7240


























































































Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-7240, Руководство по эксплуатации

Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды