HNP Mikrosysteme mzr-7240 Скачать руководство пользователя страница 59

Страница: 59 / 89

9 Software »mzr-Pump controller«

Operating manual mzr-7240

Last update: March 2019

Technical data subject to change without prior notice!

Software »mzr-Pump controller«

Install the delivered software »mzr-pump control« from both diskettes by

starting the program »Setup« on the diskette »Disk 1«. The delivered software

is compatible with Windows 95

, Windows 98

, Windows NT, Windows 2000

and Windows XP

The software »mzr-Pump controller« can you start after installation over the

start menu under »programs - HNP Mikrosysteme«. You can choose after the

start the pump type »

mzr

-7245«.

With the pump mode »Dosage« (see figure 30) you can set constant quantity

in the physical units µl (ul), mg or rotations with break. You can set the number

of repetitions or works endless. The separate dosage can define with an speed

profile, with the flexible parameter »Max. velocity« and »acceleration«. The

max. speed is programmed with 10-6.000 rpm and the acceleration is

programmed with max.1-2.000 rpm/s².

The dosage can start over the button »Start« rather through press »Enter«.

With the button »Stop« rather a new pressing of »Enter« you can break the

numerous dosage.

With the pump mode »Continuos flow« (see figure 31) you can set continuos

flow rates in the physical units ml/min, g/min and rpm. With the button »Start«

rather through press »Enter« you can start the pump for programming time

»Duration«. The button »Stop« rather a new pressing of »Enter« you can stop

the pump. With the control field »Potentiometer« you can control the speed of

the pump over the Potentiometer or the external standard signal 0 - 10 V.

Содержание mzr-7240


























































































Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-7240, Руководство по эксплуатации

Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды