HNP Mikrosysteme mzr-7240 Скачать руководство пользователя страница 75

Страница: 75 / 89

15 Problems and their removal

Operating manual for micro annular gear pumps mzr-7240

Last update: March 2019

Technical data subject to change without prior notice!

Disturbance

Cause

Solution

manufacturer.

17 The pump is noisy

Wearout of the pump or defective
components

Do not continue to operate the pump, return it
to the manufacturer for maintenance.

18 Lack of connection with the RS-232

interface

The pump is not connected.

Check the power supply 24 VDC.

Check the connection of the interface and the
null-modem cable. Change the cable if
necessary.

The drive control does not respond.

Interrupt the voltage supply for about 10 s,
connect the voltage supply again. Automatic
start of the integrated drive control

19 Overcurrent

Particles in the delivered liquid

Rinse the pump.

The pump operates with difficulty.

Dosing needle is damaged. Needle should be
cleansed, flushed or exchanged.

Tubing on the delivery side, dosing needle or
non-return valve are blocked. Cleanse, flush or
exchange the components.

Deposits inside the pump.

Flush the pump. If necessary return the pump
to the manufacturer.

20 Undervoltage

Voltage supply < 12 VDC

Check the power supply 24 VDC.

21 Overvoltage

Voltage supply > 28 VDC

Check the power supply 24 VDC. The drive
control may be damaged. Return the pump to
the manufacturer.

table 31

Problem shooting - causes and solutions.

If a disturbance that has not been mentioned in the above list, or that makes

the use of the micro annular gear pump unsafe appears, please stop the

operation of the pump without delay and contact the manufacturer.

Содержание mzr-7240


























































































Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-7240, Руководство по эксплуатации

Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды