HNP Mikrosysteme mzr-7240 Скачать руководство пользователя страница 22

Страница: 22 / 89

5 Modular system

Operating manual mzr-7240

Technical data subject to change without prior notice!

Last update: March 2019

5.2

Axial bearing module

The axial bearing module enables the pump liquids with increased pressure.

5.3

Gear box module

The gear box module enables to increase the torque of the drive in order to

deliver high viscosity liquids or to handle liquids at high differential pressure.

The gear box module is available with a 3.71 : 1 and 14 : 1 reductions for the

pump type mzr-7245. The micro annular gear pump with the gear box module

is longer of about 30 mm. The position of the controller housing to the pump

head may be shifted at about

10° depending on the pump head.

Gearing module

Controller-
housing

figure 9

mzr-7205 with the gear box module

Please take into notice that for the micro annular gear pump with the gear box

module the power supply should be specifically set (see chapter 6.5)

Please take into notice that the operating temperature range is changed from -

20 °C (-4 °F) to a maximum of 120 °C (248 °F), if the gear box module and the

heating module are combined.

Содержание mzr-7240


























































































Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-7240, Руководство по эксплуатации

Результаты поиска

Содержание mzr-7240

Отзывы:

Похожие инструкции для mzr-7240

Бренды по названию

Популярные бренды