Hitachi RCI-3.0UFE1NH Скачать руководство пользователя страница 50

Страница: 50 / 52

. CONTORL LOGIC DESCRIPTION

5.4 Auto mode

This mode can be chosen with remote controller and the set temperature can be changed
between 16~30

℃

In auto mode, the machine will choose cooling, heating or fan-only mode according to

T (

=T1-Ts).

T=T1-Ts

Running mode

T > 3

℃

Cooling

-3

℃

≤

T ≤ 3

℃

Fan-only

＜

-3

℃

Heating

Indoor fan will run at auto fan of the relevant mode. The louver operates

the

same as in relevant

mode. If the compressor keep

stopping for 10 minutes or the set temperature is modified, the

machine will choose mode according to

T again.

5.5 Evaporator low-temperature protection

DC-Inverter
AC will enter T2 protection if any of the following condition is satisfied.
Condition:

Cooling mode: When the indoor coil temp. T2 keeps lower than TE5 for 120
seconds, the compressor and outdoor fan will shut off. When T2 is higher than TE6, the
compressor and outdoor fan will restart up.

TE6

Off

TE5

Содержание RCI-3.0UFE1NH





















































Результаты поиска

Содержание RCI-3.0UFE1NH

Отзывы:

Бренды по названию

Популярные бренды

Hitachi RCI-3.0UFE1NH, Руководство по обслуживанию

Результаты поиска

Содержание RCI-3.0UFE1NH

Отзывы:

Бренды по названию

Популярные бренды