manualshive.com logo in svg

Hitachi RCI-3.0UFE1NH, Руководство по обслуживанию

Поделиться
Скачать
Hitachi RCI-3.0UFE1NH Скачать руководство пользователя страница 28

2

.TROUBLESHOOTING

NOTE 1

: 

If the indoor unit can not 

start

 or the indoor unit 

stops

 itself after 30s, at the same time the unit  

does 

not display the fault code, please check the fire and the socket of the control board. 

NOTE 2

: 

If the indoor unit display

s

 the 75,76,77,78 fault code after you turn on the unit, please check the 

TEST seat of the indoor control board or the TEST detection circuit 

to see 

whether short circuit

 

occurs

. 

NOTE 3

:

 

Overload in cooling mode  

Overload in cooling mode 

sr. 

The root cause 

Corrective measure 

1 

The refrigerant is excessive

.

 

Discharge the refrigerant, and recharge 
the refrigerant refer

ring

 to the rating label

.

  

2 

The outdoor ambient temperature is too high

.

 

Please use 

it 

within allowable temperature range

.

 

3 

S

hort-circuit

 occurs in the air outlet and air inlet of 

the outdoor unit.

Adjust  the  installation  of  the  outdoor  unit 
refer

ring

  to the user manual

.

  

4 

The  outdoor  heat  exchanger  is  dirty,  such 
as condenser

.

  

Clean the heat exchanger of the outdoor unit, 
such as condenser

.

  

5 

The speed of the outdoor fan motor is too low

.

 

Check the outdoor fan motor and fan capacitor

.

 

6 

The  outdoor  fan  is  broken  or  the  outdoor  fan 
is blocked

.

  

Check the outdoor fan

.

 

7 

The air inlet and outlet has been blocked

.

 

Remove the 

obstructions

.

 

8 

The expansion valve or the capillary fail

s.

 

Replace the expansion valve or the capillary

.

 

NOTE 4

:

 

Over load in heating mode 

Overload in heating mode 

sr. 

The root cause 

Corrective measure 

1 

The refrigerant is excessive

.

 

Discharge the refrigerant, and recharge 
the refrigerant refer

ring

 to the rating label

.

  

2 

The indoor ambient temperature is too high

.

 

Please use 

it 

within allowable temperature range

.

 

3 

S

hort-circuit   

occurs in the air outlet and air 

inlet of the indoor unit.

Adjust the installation of the indoor unit refer

ring

 

to the user manual

.

  

4 

The indoor filter is dirty

.

 

Clean the indoor filter

.

 

5 

The speed of the indoor fan motor is too low

.

 

Check the indoor fan motor and fan capacitor

.

 

6 

The indoor fan is broken or the outdoor fan 
is blocked

.

  

Check the indoor fan

.

 

7 

The air inlet and outlet has been blocked

.

 

Remove the 

obstructions

.

 

8 

The expansion valve or the capillary fail

s.

Replace the expansion valve or the capillary

.

 

26

Содержание RCI-3.0UFE1NH





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды