manualshive.com logo in svg

Hillrom Compella, Инструкция по эксплуатации

Поделиться
Скачать
Hillrom Compella Скачать руководство пользователя страница 88

Accessories

74

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

Pressure Transducer Holder (P3670A05) and Respiratory Circuit Holder 
(P3670A01)

WARNING:

To help prevent personal injury and/or equipment 
damage, follow these warnings and cautions:

•

Warning

—After you raise or lower the head 

section, make sure the holder is in the correct 
position.

•

Warning

—When the holder is installed, use 

caution when you move around the bed, 
move the bed, or transfer a patient in or out of 
the bed. 

•

Warning

—Use the holder for medical 

equipment only. 

•

Warning

—During rotation, monitor the patient rotation angle and make sure that the patient 

stays centered on the surface with shoulders correctly aligned, and that there is sufficient slack 
in lines for patient movement and surface rotation.

•

Warning

—Do not attach height sensitive devices or transducers with drainage capacity.

•

Warning

—Do not exceed the 2.2 lb (1 kg) load capacity of each holder. 

•

Warning

—Do not use a holder to move the bed. 

The pressure transducer holder and respiratory circuit holder are used to hold respiratory ventilator 
circuits and pressure transducers and keep them in position. The P3670A01 is the tube holder 
configuration, and the P3670A05 is the transducer configuration. The holders can be mounted on either 
or both corners of the head section. Refer to the manufacturer’s instructions for operation.

To Install

1.

Loosen the knob on the bottom of the holder bracket.

2.

Slide the holder bracket on to the bed mount bracket until it stops.

3.

Tighten the knob.

4.

Put the holder in the applicable position.

p

Содержание Compella





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды