manualshive.com logo in svg

Hillrom Compella, Инструкция по эксплуатации

Поделиться
Скачать
Hillrom Compella Скачать руководство пользователя страница 70

Surface Features and Controls

56

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

•

Warning

—To avoid the risk of electric shock, the air supply unit must only be connected to a 

supply mains with protective earth. 

•

Warning

—If the unit displays unintelligible information, stop using the device immediately 

and call for service. 

•

Warning

— To avoid the risk of a patient fall while the CLRT and Turn Assist modes are active—

–

Before you start either mode, make sure the bed’s width is sufficient for the patient to turn.

–

Do not lower the siderails while either mode is active, Pause or turn off the mode before 
you lower a siderail. 

•

Warning

—The power cord for the air supply unit is equipped with magnets to hold the cord in 

position on the bed frame. Exposure to magnetic fields may alter the functioning of implanted 
devices such as pacemakers and defibrillators.

•

Warning

—Do not use device in conjunction with flammable agents.

•

Warning

—Do not connect the power cord to an extension cord or multiple outlet strip. There is 

a risk of overheating and fire may cause injury or damage.

•

Warning

—Only connect items that have been specified as part of the device or specified as 

being compatible with the device.

•

Warning

—Check that the power ratings of the supply mains are sufficient to power the air 

supply unit.

•

Warning

—Use of accessories, transducers, and cables other than those specified, with the 

exception of transducers and cables sold by the manufacturer of the device as replacement 
parts for internal components, may result in increased emission and/or decreased immunity of 
the device. 

•

Warning

—Observe precautions regarding EMC; install and put into service according to the 

EMC information provided in the accompanying documents.

S

UPPORT

 S

URFACE

 O

PTIONS

The bed has two support surface options:

•

Compella™ Therapy Surface with Turn Assist or Turn Assist with CLRT (see “Compella™ Therapy 
Surface” on page 59)—the therapy surface system consists of the air supply unit, therapy 
surface, power cord, and communication cable

•

Compella™ Foam Surface with inflatable side bolsters and foot section (see “Compella™ Foam 
Surface with Inflatable Side Bolsters” on page 67)—the foam surface system consists of the air 
supply unit, foam surface, power cord, and communication cable

For assistance with setup, use, or maintenance of the support surface and air supply unit or to report 
issues with the system, contact your facility authorized maintenance person or Hill-Rom Technical 
Support.

Содержание Compella





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды