manualshive.com logo in svg

Hillrom Compella, Инструкция по эксплуатации

Поделиться
Скачать
Hillrom Compella Скачать руководство пользователя страница 34

Information Indicators

20

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

Off

—no lights will show on the indicator if the battery charge is too low to operate the bed.

NOTE:

There will be a 

double

 beep if the battery has gone to sleep and you press a bed articulation control. 

This is the only time you will hear a 

double

 beep.

CAUTION:

Caution

—For transport, a fully-charged battery is preferred; however, if the battery charge is low, 

before you unplug the bed, put the bed in the correct position before any transport, and connect the 
bed to AC power as soon as possible.

If the Battery Indicator changes from Charged to Low consistently within four hours of being 
disconnected from AC power, replace the battery.

While on battery power, the bed will operate as follows:

•

All of the bed functions will operate except for width adjustment. For manual width 
adjustment, see “Manual Width Control” on page 34.

•

The integrated air surface will stay inflated, but it will not adjust pressures.

•

The Bed Exit and Scale functions will 

not

 operate.

Service Required

Hip Position Locator (earlier bed versions)

The hip position label on the intermediate siderails identifies the correct 
position of the patient's hips while on the bed.

Correct placement of the patient increases the effectiveness of the SlideGuard® 
Technology. This is designed to minimize patient migration to the foot end of 
the bed when you raise the head section.

Head Pivot Locator 

The head pivot locator label on the intermediate siderails identifies the 
approximate pivot point of the head section.

Correct placement of the patient increases the effectiveness of the SlideGuard® 
Technology. This is designed to minimize patient migration to the foot end of 
the bed when you raise the head section.

The Service required indicator, on the caregiver control panel, flashes when the bed 
detects a malfunction. Contact your facility-authorized maintenance person or 
Hill-Rom Technical Support for assistance. 

Bed Not Down

When the bed is not in its lowest position, the 

Bed Not Down 

indicator comes on.

Содержание Compella





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды