manualshive.com logo in svg

HIKVISION DS-KAD1040, Руководство пользователя, Страница: 77 / 80

Поделиться
Скачать
HIKVISION DS-KAD1040 Скачать руководство пользователя страница 77

A. Cables

Cables and Wiring

●

When there are multiple cores in one parallel line, only one pair of closed

cores are allowed to transmit signal. It is not allowed to use multiple pair

of cores in one cable to transmit signal.

●

When using parallel lines, it is suggested to use those with shielding layer.

If dual core or multiple core parallel lines without shielding layer are

routed, stability of signal transmission can be effected. You need to run a

test before installation.

●

Impedance of cable should not be over suggested value, or distributor

cannot transmit enough power to indoor station or door station.

●

Strong electricity and weak electricity cannot be wired in the same route,

they need to be wired separately and the distance should be more than

0.5 meter.

●

All the cables used need to follow the restriction in the following table.

Table A-1 Wiring Cables

Routin

g Path

Twisted Pair

Parallel Lines

17AW

G

20AW

G

24AW

G

23AW

G

17AW

G

20AW

G

24AW

G

23AW

G

DS-

KAD70

40 -

DS-

KD800

3-IME2

Transm

ission

Distanc

e ≤ 50

m

Transm

ission

Distanc

e ≤ 60

m

Transm

ission

Distanc

e ≤ 35

m

Transm

ission

Distanc

e ≤ 35

m

Transm

ission

Distanc

e ≤ 50

m

Transm

ission

Distanc

e ≤ 50

m

Transm

ission

Distanc

e ≤ 35

m

Transm

ission

Distanc

e ≤ 35

m

DS-

KAD70

40 -

Transm

ission

Distanc

Transm

ission

Distanc

Transm

ission

Distanc

Transm

ission

Distanc

Transm

ission

Distanc

Transm

ission

Distanc

Transm

ission

Distanc

Transm

ission

Distanc

Video Intercom Two-Wire Bundle User Manual

66

Содержание DS-KAD1040

















































































Отзывы:

Нет отзывов