manualshive.com logo in svg

HIKVISION DS-KAD1040, Руководство пользователя, Страница: 20 / 80

Поделиться
Скачать
HIKVISION DS-KAD1040 Скачать руководство пользователя страница 20

3.2 Wiring Description

Typical application of the system is shown as below.

Figure 3-3 Wiring

Note

●

Up to 10 indoor stations can be connected hand-by-hand.

●

Up to 150 indoor stations can be connected to one terminal of the distributor.

●

When connecting the doorbells to indoor stations, up to 85 indoor stations can be

connected to one terminal of the distributor.

Caution

Make sure all the related equipment is power-off during the wiring and installation.
Two-Wire door station should be connected to CH1 (48 V,15 W) of the distributor

with 2-wire cables.
Two-Wire Analog Distributor should be connected to any terminal of CH2 to CH5 (48

V,15 W) of the distributor with 2-wire cables.
Network door station can be connected to LAN(PoE) of the distributor with Network

Cable.
1 distributor can only connect 1 door station to build the communication.
The distributor supports standard PoE.

Video Intercom Two-Wire Bundle User Manual

9

Содержание DS-KAD1040

















































































Отзывы:

Нет отзывов