manualshive.com logo in svg

HIKVISION DS-KAD1040, Руководство пользователя, Страница: 74 / 80

Поделиться
Скачать
HIKVISION DS-KAD1040 Скачать руководство пользователя страница 74

security system, changing the password monthly or weekly can better

protect your product.

6.4.2 Network Settings

TCP/IP Settings

TCP/IP settings must be properly configured before you operate the device over

network. The device supports IPv4.
Steps
1. Click Network → Basic Settings → TCP/IP to enter the settings page.
2. Configure the network parameters.

-

Check DHCP, the device will get the parameters automatically.

-

Set the IPv4 Address, IPv4 Subnet Mask and IPv4 Default Gateway manually.

3. Click Save to enable the settings.

Port Settings

Steps
1. Click Network → Basic Settings → Port to enter the settings page.
2. Set the ports of the device.

HTTP Port

The default port number is 80, and it can be changed to any port No. which is

not occupied.

Server Port

The default server port number is 8000, and it can be changed to any port No.

ranges from 2000 to 65535.

3. Click Save to enable the settings.

SIP Setting

Steps
1. Click Network → Basic Settings → SIP to enter the settings page.

Video Intercom Two-Wire Bundle User Manual

63

Содержание DS-KAD1040

















































































Отзывы:

Нет отзывов