manualshive.com logo in svg

HIKVISION DS-KAD1040, Руководство пользователя, Страница: 24 / 80

Поделиться
Скачать
HIKVISION DS-KAD1040 Скачать руководство пользователя страница 24

Before You Start

●

Make sure the device in the package is in good condition and all the assembly

parts are included.

●

The power supply the indoor station supports is 48 VDC. Please make sure your

power supply matches your indoor station.

●

Make sure all related equipments are power-off during the installation.

●

Check the product specification for the installation environment.

There are 2 size of the gang boxes adapted to the device.

●

Size 1: 75 mm (width) × 75 mm (length) × 50 mm (depth).

●

Size 2: 55 mm (width) × 101 mm (length) × 38.5 mm (depth).

The dimension of mounting plate is shown as below.

Figure 4-3 Mounting Plate

Steps
1. Cave a hole in the wall.

Note

The suggested dimension fo the installation hole should be larger than the gang

box.

2. Insert a gang box to the hole chiseled on the wall.
3. Fix the wall mounting plate to the gang box with 2 screws.

Video Intercom Two-Wire Bundle User Manual

13

Содержание DS-KAD1040

















































































Отзывы:

Нет отзывов