manualshive.com logo in svg

HIKVISION DS-KAD1040, Руководство пользователя, Страница: 66 / 80

Поделиться
Скачать
HIKVISION DS-KAD1040 Скачать руководство пользователя страница 66

5 Activation

5.1 Connect to Network

The network distributor supports two ways to connect to network.

5.1.1 Connect to Wired Network

You can connect the device to the network via connecting network cables.
Steps
1. Use the network cable to connect your computer to distributor.
2. Enter the default IP address of the device in the address bar of web browser.

What to do next

Activate the device and login to configure parameters remotely.

5.1.2 Connect to Wireless Network

The network distributor supports Wi-Fi AP mode. You can connect the device to the

network via wireless network.
Steps
1. Enable the Wi-Fi AP mode of the device.
2. Connect the computer to distributor via wireless network.
3. Enter any content in the address bar of web browser, the configuration page of

the distributor will pop up automatically.

What to do next

Activate the device and login to configure parameters remotely.

5.2 Activate Device via Client Software

You can only configure and operate the door station after creating a password for

the device activation.
Default parameters of door station are as follows:

Video Intercom Two-Wire Bundle User Manual

55

Содержание DS-KAD1040

















































































Отзывы:

Нет отзывов