High Lifter PGL-KIT-RZRT Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 34

High Lifter PGL-KIT-RZRT Скачать руководство пользователя страница 8

PGL-KIT-RZRT

8

FRONT INSTALLATION

1.

PREPARE VEHICLE

[THE FOLLOWING INSTRUCTIONS TAKE PLACE ON THE

PASSENGER SIDE

]

a.

Begin by loosening the lug nuts on both front tires.

b.

Raise the unit, using a suitable lifting device or procedure, until the front tires are off the ground.

c.

If using a floor jack with stands, chock the rear wheels to prevent the unit from rolling. If using jack stands,
make sure the stands are placed under the frame and not the body.

d.

Make sure the unit is stable and secure. Remove wheel nuts and front wheels.

2.

REMOVAL OF FRONT BRAKE CALIPER AND HUB

a.

Remove the upper & lower caliper mounting bolts (15mm).

b.

Remove the front brake scraper from the caliper, it is no longer needed. (8mm)

c.

It is not necessary to remove the brake line from the caliper at this time. Leave the brake hose attached to
the caliper and

hang the calipers out of the way. Take precautions to ensure the brake hose isn’t stretched

or pinched.

d.

Retain the factory bolts & nuts. They will be reused during the installation of the bolt-on portal boxes &
mounting brackets.

«
...
6
7
8
9
10
...
»

Содержание PGL-KIT-RZRT



































Отзывы:

Нет отзывов