Hidrex DP450 Скачать руководство пользователя страница 17

  Rev. 1.4 / 02-16-2017        

DP450 Tap Water Iontophoresis System User Manual

 

 
 

 

17 

display shows the remaining treatment time and the selected dose  in volts. 
When  you  continue  the  treatment,  the  ACTIVE  LED 

  will  light  up  again 

and the dose display changes to  zero, before it slowly  increases to the de-
sired value. 

4) Ending a treatment session: 

When  the  treatment  time  is  up,  the  treatment  dose  is  automatically  lowered  to 
zero. Please keep your hands and feet in the trays (or the axillary pads in place, 
respectively) until the dose display reads “End“. 

Remove  the  treatment  area  from  the  water  source  (trays  or  pads)  and 
THEN switch the device off

Important Advice for Conducting Treatments 

For  your safety,  your HIDREX treatment system comes equipped  with sev-
eral protective circuits. 

 
Immersion monitoring 

Immersion  monitoring  is  a  built-in  feature  that  detects  when  the  treatment 
electrical  current  circuit  is  closed  due  to  immersion  of  the  palms  or feet,  or 
placement  of  the  pads  under  the  arms.    The  ACTIVE  LED 

  will  light  up 

when the circuit is closed and treatment is active. 

Over Treatment Protection (OTP) Feature

 

If your skin is dryer than normal

1

, the dose cannot be increased (protection 

against  over-treatment).  Your  HIDREX  system  automatically  checks  your 
specific  skin  conductance.  If  your  skin  conductance  is  beyond  the  preset 
threshold,  the  protection  circuit  is  activated  and  locks  the  system.  The 
ACTIVE LED 

 does not  light up, even  when the treatment current path is 

closed. 

Hint: 

To  double-check  if  over-treatment  protection  has  been  activated  for  you 
(and  that  it  is  not  a  fault  of  the  device),  you  can  run  a  quick  operational 
check of the device to confirm that it is your skin conductance and not the 
device.    Simply  take  one  cable  and  insert  each  end  into  a  jack  on  the 
module AFTER the device is in Programming Mode.  This closes the cir-
cuit; the ACTIVE LED   will light up if the device is working properly.

 

If over-treatment protection is activated, you should interrupt your treatment 
course for at least one week until excessive perspiration returns. 

Please contact us if the OTP feature has been activated 

AND

 you still have 

excessive  perspiration,  which  is  a  situation  that  may  arise  in  very  rare  cir-
cumstances. 

                                           

1

 This does not relate to the surface skin layer, but to the moisture content of the deeper skin layers, an 

indicator of the extent of hyperhidrosis.  

Содержание DP450





























Отзывы: