hexinverter Mutant Hot Glue Скачать руководство пользователя страница 20

Страница: 20 / 22

04.24.2015

Mutant Hot Glue DIY assembly manual v1.05

PG20

HEXINVERTER ÉLECTRONIQUE, 2015

STEP 2:

Deactivate the compressor’s gain reduction, with the following settings…

STEP 3:

While viewing and comparing the COMP output signal to the input signal, adjust the

SYMMETRY ADJUST

control for best vertical symmetry. See the images below for how to do this…

The upper and lower peaks of the output waveform (blue) are not symmetrical. You can tell

by inspecting the vertical distance between the yellow and blue waveforms.

At first glance, this might seem okay – but pay close attention! – the output waveform (blue) is

above and below

the input

waveform! This is not correct, as we will see in the following correct example.

GAIN = 0dB

BLEND = WET (100%)

THRESHOLD = +26dBu

RATIO = MAXIMUM

POOR SYMMETRY

Содержание Mutant Hot Glue























Результаты поиска

Содержание Mutant Hot Glue

Отзывы:

Похожие инструкции для Mutant Hot Glue

Бренды по названию

Популярные бренды

hexinverter Mutant Hot Glue, Инструкция по сборке

Результаты поиска

Содержание Mutant Hot Glue

Отзывы:

Похожие инструкции для Mutant Hot Glue

Бренды по названию

Популярные бренды