4
21/03/2019 Rev.2 (04/12/2019)
*Please make sure before connecting the bed that the electrical installation complies with the standard NF C 15 100; if your installation
doesn't comply with this standard, HERDEGEN company would decide to accept or refuse any complains regarding the electical
components of this bed.*In case of troubles or doubt, please ask the operator or HERDEGEN SAS.
*The bed shall be connected directly to the electrical power. Do not use electrical outlets and extension cords.
*Don‘t place several electrical outlets under the bed, as leaking liquids can be a fire hazard.
*Unplug the power cable from wall outlet, before moving the Home Care bed around.
*Roll the cable on the support when moving the Home Care bed around so that they are not crushed or squeezed.
*Check the power cable regularly for damages (crushed, bare, sheared, porous..) and particularly :
1/after every mechanical strains(for example : rolling over the cables).
2/after having moved the Home Care bed and before pluging in the power cable.
3/every month in a normal use.
*Regularly check the cable strain relief, it must be in perfect condition.
*Don‘t store anything under the bed.
*Lower the Home Care bed to its lowest position when leaving the patient unattented, thus you reduce the risk of injuries when the
patient leaves-enters the bed.
*Hang the remote control on the siderail or on the trapeze pole to avoid it from falling down. Make sure that the wire is correctly
positionned to avoid squeezing or crushing the cables. Lock the remote if necessary by removing the key on it.
*In case of doubt, if the bed appears to be damaged or if you suspect a malfunction, immediately unplug it from wall outlet, mark it
as „DEFECTIVE“ and contact your supplier.
1.3 Product description
*The Home Care bed AMPLI + ® works as a convenient solution for taking care of infirm, disabled people in nursing homes or at
home.
*This bed can be used for care under the instructions of a physician and can serve in diagnosing, treatment and observation of a
patient. It is therefore equipped with a locking mechanism for the electrical adjustment functions.
*This bed has no special connector for a potential equalization.
*Maximum permitted load on the bed 170 kg (weight of P weight of accessories), maximum user‘s weight 135kg
!
135 kg
!
170 kg
*This bed shall not be used for patient under 146 cm and less than 40kg.
*This be shall only be operated by trained staff.
*This bed can be reused and rented.
*This bed can be moved accross the building, even with the patient lying on it.
*This bed must be used in a proper way as detailed in this instruction manual. Any other uses are strictly prohibited.
*This bed shall be used only per adults.
1.4 Technical information
The AMPLI + ® Home Care bed is delivered in parts, ready to be mounted. Siderails, Pole and bed ends are fastened on the bed
frame.
The bed is made of Epoxy steel and has 2 or 3 motors according to the version.
The bed can be mounted per ONE SINGLE qualified person. It consists in : one slats frame (in 2 parts), one scissor frame, 2 side rails,
1 lifting pole with trapeze, 2 bed ends. The bed has 2 holders for the lifting pole. It is equipped with 4 castors, 2 of them with brakes.
1.4.1 Slats bed frame
The Home Care bed exists in 2 versions :
-with 2 motors (4-sections mattress support) what means an electrical backrest, an electrical Hi-low adjustment, and a manual
legrest.
- with 3 motors (4-sections mattress supports) what means electrical backrest, Hi-low and legrest. Note that the legrest can be also
adjusted manually to reach the desired position.
4-section mattress support : a movable backrest, a fixed middle section, a movable upper leg support and a movable lower leg support.
The frame is made of welded steel covered with a PE powder coating. All mobile parts, as well as the height of the lying surface can
be adjusted by means of 24V remote control. Note that the upper leg support can be adjusted manually to get the desired position.
3-section mattress support : a movable backrest, a fixed middle section, a movable upper leg support and a movable lower leg support.
The frame is made of welded steel covered with a PE powder coating. All mobile parts, as well as the height of the lying surface can
be adjusted by means of 24V remote control excepts the legrest, that must be adjusted manually.
1.4.2 Side rails
The bed has 2 side rails which can be raised as a barrier or lowered when not needed. The side rails prevent the patient from
accidentally falling out of the bed.
Distributør i Norge:
Gymo AS - www.gymo.no
(+47) 4000 3522 - [email protected]
