Hellenbrand H-151 Series Скачать руководство пользователя страница 19

Страница: 19 / 40

STEP 15CS –

Press the





buttons until selection of first cycle appears in left upper corner, in this

example BACKWASH is selected. Press NEXT to go to Step 16CS. Press REGEN to return to previous

step.

STEP 16CS –

Press the





buttons until selection of second cycle appears in left upper corner, in

this example Regenerant Draw DN is selected. For a H151 control valve: prior to selecting DN or UP or

not selecting a regenerant flow cycle, verify the correct valve body, main piston, regenerant piston and

stack are being used and the injector or injector plug(s) are in the correct location. Press NEXT to go to

Step 17CS. Press REGEN to return to previous step.

STEP 17CS –

Press the





buttons until selection of third cycle appears in left upper corner, in this

example BACKWASH is selected. A second backwash mode is recommended on iron applications > 1.0

ppm. Press NEXT to go to Step 18CS. Press REGEN to return to previous step.

STEP 18CS –

Press the





buttons until selection of fourth cycle appears in left upper corner, in this

example RINSE is selected. Press NEXT to go to Step 19CS. Press REGEN to return to previous step.

STEP 19CS –

Press the





buttons until selection of fifth cycle appears in upper left corner. Press

NEXT to go to Step 20CS. Press REGEN to return to previous step.

STEP 20CS –

Press the





button until last regeneration cycle; END appears (up to 9

regeneration modes are possible).

End must be selected as last cycle.

Press NEXT to go to Step

21CS.

STEP 21CS –

Press the





button to select “LBS” or MIN as brine tank fill units. Select LBS with

standard 0.5 gm brine refill flow control. Select minutes if using larger brine refill flow control.

Factory

setting is LBS.

STEP 22CS –

Press the





button to select number of standard regenerations which would trigger

one alternate brine fill amount. Range: 1-99.

Factory setting is Off.

Press NEXT to go to Step 23CS.

STEP 23CS –

Select amount of salt to be used when alternate regeneration requested. This screen is

not displayed if off is selected in previous step. Softener Range 0.1–200 lbs. Filter Range 0.05–20.0

Gallons.

CYCLE 2

REGENERANT DRAW DN

SET

STEP 16CS

CYCLE 3

BACKWASH

SET

STEP 17CS

CYCLE 4

RINSE

SET

STEP 18CS

CYCLE 5

FILL

SET

STEP 19CS

CYCLE 6

END

SET

STEP 20CS

REGENS

ALT FILL TRIGGER

SET

OFF

STEP 22CS

15.0

ALT FILL AMOUNT

SET

LBS

STEP 23CS

CYCLE 1

BACKWASH

SET

STEP 15CS

FILL UNITS

SET

LBS

STEP 21CS

➔

Содержание H-151 Series









































Результаты поиска

Содержание H-151 Series

Отзывы:

Похожие инструкции для H-151 Series

Бренды по названию

Популярные бренды

Hellenbrand H-151 Series, Руководство пользователя

Результаты поиска

Содержание H-151 Series

Отзывы:

Похожие инструкции для H-151 Series

Бренды по названию

Популярные бренды