manualshive.com logo in svg

Hefter TF MEGA-A, Инструкция по эксплуатации, Страница: 64 / 71

Поделиться
Скачать
Hefter TF MEGA-A Скачать руководство пользователя страница 64

4-10

Chapter4 Troubleshooting Guide

Symptom

Cause

Solution

Paper slips at the paper feed section 

frequently.

The paper feed pressure is weak.

Move the paper feed pressure 

adjustment knob to increase the 

paper feed pressure level. 

(

p.2-4)

The separating pressure is strong.

Turn the separating pressure 

adjustment dial to decrease the 

separating pressure. (

p.2-4)

The paper feed ring is dirty.

Clean it with alcohol. (

p.5-2)

The sheets of paper are sticking to 

each other and cannot be separated.

Fan the paper well. (

p.1-12)

The paper is outside the 

specifications.

Use paper that meets specifications. 

(

p.6-1)

The side guides press against the 

paper too tightly.

Set the side guides so that they 

push against the paper lightly. 

(

p.2-3)

A trouble has occurred inside the 

machine.

Call your dealer. 

Paper jams frequently.

The rubber roll is dirty.

Clean it with alcohol. (

p.5-1)

Paper shreds are stuck inside the 

paper conveyance passage.

Check inside the machine and 

remove any paper shreds.

The stacker rollers position is not 

correct.

Adjust the position of the stacker 

rollers.(

p.3-9)

The paper is curled.

Straighten the paper curl.

The guide plate unit is left attached 

to the paper ejection plate.

Remove the guide plate unit. 

(

p.3-6 )

Static electricity has occurred in the 

paper.

Spray a commercially-available air 

duster on the rubber roll.

Paper slips in the vertical direction.

The folding position is not correct.

Correct the folding misalignment. 

(

p.3-20)

Paper slips in the horizontal 

direction.

The paper is stacked unevenly.

Stack the paper neatly on the paper 

feed tray. (

p.1-12)

There is space between the paper 

and side guide.

Set the side guides so that they 

push against the paper lightly. 

(

p.2-3)

The rubber roll is deformed.

Call your dealer.

Paper jam at the rubber roll when 

thick paper or cross folded thick 

paper is folded into two.

The paper is outside the 

specifications.

Use paper that meets specifications. 

(

p.6-1 )

The space inside the internal paper 

conveyance passage is narrow.

Adjust the position of the stopper 
using the 

 key. (

p.3-1)

Small paper is fed continuously 

(stream-fed).

The paper is outside the 

specifications.

Use paper that meets specifications. 

(

p.6-1)

The paper feed pressure is strong.

Move the paper feed pressure 

adjustment knob to decrease the 

paper feed pressure level. 

(

p.2-4)

Содержание TF MEGA-A








































































Отзывы:

Нет отзывов