Hefter TF MEGA-A Скачать руководство пользователя страница 62

Страница: 62 / 71

4-8

Chapter4 Troubleshooting Guide

3. Error Messages

When a paper jam has occurred or the top cover is open, an error message is displayed on the LCD display.
Follow the procedures below to fix the error. If you cannot solve the trouble, contact your dealer.

Message

Cause

Solution

No paper

When the power is turned on, there

is no paper on the paper feed tray.

Stack paper on the paper feed tray.

No paper/****(the number of folded

paper)

After paper is fed and folded, there

is no paper left on the paper feed

tray.

Stack paper on the paper feed tray.

Feed tray error

When the paper feed tray is lowered,
the

key or

key was

pressed.

Lower the paper set lever. The paper

feed tray will go up.

Top cover open

The top cover is open.

Close the top cover.

Feed error

A paper jam has occurred at the

paper feed section.

Remove the jammed paper and

press the C key. (

p.4-1

A mis-feed has occurred at the

paper feed section.

Stack paper properly on the paper

feed tray and press the C key.

(

p.1-12, 4-2)

Jam exit

A paper jam has occurred at the

paper exit section.

Remove the jammed paper and

press the C key. (

p.4-7)

Plate1 set error

The first folding plate has not been

installed properly.

Install the first folding plate properly.

(

p.1-6)

Plate2 set error

The second folding plate has not

been installed properly.

Install the second folding plate

properly. (

p.1-5)

Plate1 cable err

The control cable of the first folding

plate has not been connected

properly.

Turn off the power and connect the

control cable properly. (

p.1-6)

Plate2 cable err

The control cable of the second

folding plate has not been

connected properly.

Turn off the power and connect the

control cable properly.(

p.1-6)

Main motor err

A paper jam has caused the main

motor to become overloaded.

Remove the jammed paper and turn

off and on the power.

Stack motor err

A paper jam has caused the

positioning motor of the stacker to

become overloaded.

Remove the jammed paper and turn

off and on the power.

Plate1 motor err

A paper jam jam has caused the

stopper motor of the first folding

plate to become overloaded.

Remove the jammed paper from the

leading end of the first folding plate,

then turn off and on the power.

Plate2 motor err

A paper jam has caused the stopper

motor of the second folding plate to

become overloaded.

Remove the jammed paper from the

leading end of the second folding

plate, then turn off and on the

power.

Содержание TF MEGA-A








































































Результаты поиска

Содержание TF MEGA-A

Отзывы:

Hefter TF MEGA-A, Инструкция по эксплуатации, Страница: 62 / 71

Результаты поиска

Содержание TF MEGA-A

Отзывы: