Hefter TF MEGA-A Скачать руководство пользователя страница 44

Страница: 44 / 71

3-14

Chapter3 Advanced Operation

4-1. Cross Folding Standard Size Paper

The paper size that can be cross folded is A3, B4, A4 and B5 (EU)/ LD, LG and LT (North America).
The following describes the cross single folding procedures of A3 (EU)/LG (North America) size paper.

Only short edge feed is available for

cross folding.

Fold A3 (EU)/LG (North America) size

paper into two according to Chapter

1 "BASIC OPERATION" "1.Standard

Folding of Standard Paper" ( p.2-1).

Press along the folded line of the single-

folded paper firmly with your fingers

to prevent the paper from slipping and

buckling in the horizontal direction

when folded.

Paper

Side guide

Paper set lever

36 mm/1-1/2 inches

Raise the paper set lever and stack the

single-folded paper on the paper feed

tray with the folded line facing the non-

operator's side.

The amount of paper stacked on the

paper feed tray should be approximately

2/3 (36 mm/1-1/2 inches) of the height of

the side guide.

Loosen the fixing screws of the side

guides.

Side guide

Fixing screw

After pressing the side guide to each

side of the paper lightly, tighten the

screws to secure the side guides.

Содержание TF MEGA-A








































































Результаты поиска

Содержание TF MEGA-A

Отзывы:

Hefter TF MEGA-A, Инструкция по эксплуатации, Страница: 44 / 71

Результаты поиска

Содержание TF MEGA-A

Отзывы: