manualshive.com logo in svg

Heat&GloGlo 6000CF-OAK-IPI, Руководство пользователя, Страница: 50 / 51

Поделиться
Скачать
Heat&GloGlo 6000CF-OAK-IPI Скачать руководство пользователя страница 50

53

Heat & Glo  •  6000CF-OAK-IPI  •  2092-900  Rev. 

I

  •  1/06

D.   Limited Lifetime Warranty

LIMITED LIFETIME WARRANTY

HEAT & GLO GAS APPLIANCE PRODUCTS

BASIC ONE-YEAR WARRANTY.  HEAT & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington

Boulevard, Lakeville, MN 55044, (“HEAT & GLO”) warrants to the original owner that your new HEAT & GLO Gas Appliance (the “Product”)

will be free from defects in materials and workmanship for a period of one year from the date of in

stallation.  During the first year, HEAT & GLO

will replace or repair, at its discretion, any defective components at its sole cost and expense, including payment of all reas

onable labor costs

incurred in replacing or repairing such components. This basic warranty is subject to the conditions, 

exclusions and limitations described

below.

EXTENDED LIFETIME COVERAGE.  HEAT & GLO warrants that the firebox, heat exchanger, log(s), and burner will not be defective in

material or workmanship during the period the Product is owned by the original owner, subject to the following conditions, exclusions and

limitations described below.

CONDITIONS, EXCLUSIONS AND LIMITATIONS:

1. This warranty applies to the original owner only and is nontransferable.

2. This warranty applies only to Products installed in the United States of America or Canada.

3. This warranty is limited to the replacement or repair of defective components or workmanship and HEA

T & GLO may fully discharge all

obligations under this warranty by repairing or replacing, at its discretion, the defective components. The maximum amount recoverable

under this warranty is limited to the purchase price of the Product and, if HEA

T & GLO is unable to provide replacement or repair in an

expedient and cost-effective manner, HEAT & GLO may discharge all obligations under this warranty by refunding the purchase price

of the Product.  IN NO EVENT SHALL HEAT & GLO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED

BY DEFECTS IN THE PRODUCT.

4. Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components under 

the Limited

Lifetime Warranty are not covered by this warranty, except as provided for under the Basic One-Year Warranty.

5. Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered by this

warranty unless expressly authorized and approved by HEAT & GLO in writing.

6. Any damages caused by environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of th

e structure,

air handling devices such as exhaust fans or forced air furnaces, or other such causes are not covered by this warranty

.

7. This warranty will be void if:

a) The Product is not installed, operated and maintained in compliance with local building codes and with the instructions in the

Installer’s Guide, Owner’s Guide and Listing Agent Identification Label furnished with the Product.

b) Any parts or components made by other manufacturers are added or used in the Product, unless expressly authorized and

approved by HEAT & GLO in writing.

c) Any service work is performed on the Product by anyone other than an authorized HEAT & GLO representative.

d) The Product is damaged due to shipping, improper handling, accident, abuse or misuse.

e) Fuels other than those specified in the Installer’s Guide and Owner’s Guide are used.

f ) Modification was made to the Product which was not expressly authorized and approved by HEAT & GLO in writing.

EXCEPT TO THE EXTENT PROVIDED BY LAW, HEAT & GLO MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY

SPECIFIED HEREIN. THE DURA TION OF ANY IMPLIED WARRANTY IS LIMITED T O THE DURATION OF THE W ARRANTY

SPECIFIED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incident

al or consequential

damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which

vary from State to State.

If warranty service is needed you should contact your installing dealer and if the installing dealer is 

unable to provide necessary parts or

components, contact the nearest authorized HEAT & GLO dealer or supplier.

NOTES TO CUSTOMER:

1. In order to insure proper installation, operation and maintenance HEAT & GLO strongly recommends annual servicing by an authorized

HEAT & GLO dealer.

2. Please complete this information and retain this warranty in a safe place for future reference: Installation Date:___________

_______

Model #:______________________ Serial #:__________________________ Installing Contractor:_________________________

3. HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications and prices of the Product.

HEAT & GLO also reserves the right to discontinue styles and products.

© 2005 Hearth & Home Technologies Inc.

060-981D   3/05

Содержание 6000CF-OAK-IPI




















































Отзывы:

Нет отзывов