Heat&GloGlo 6000CF-OAK-IPI Скачать руководство пользователя страница 40

40

Heat & Glo  •  6000CF-OAK-IPI  •  2092-900  Rev. 

I

  •  1/06

B.   Lighting Appliance

Intellifire Ignition

Final Inspection by

_________________________________

1.

Turn off all electric power to the appli-

ance.

2.

This appliance is equipped with an ig-

nition device which automatically lights

the burner. Do not try to light the burner

by hand.

3.

Wait  five  (5)  minutes  to  clear  out  any

gas. Then smell for gas, including near

the floor. If you smell gas, STOP! Fol-

low "B" in the Safety Information located

on the left side of this label. If you don't

smell gas, go to next step.

4.

Turn on all electric power to the appli-

ance.

5.

To  light  the  burner,  flip  the  ON/OFF

switch to the “ON” position. (The ON/

OFF switch may include a wall switch

if  so  equipped).

6.

If the appliance will not operate, fol-

low the instructions “To Turn Off Gas

to Appliance” and call your service tech-

nician  or  gas  supplier.

LIGHTING

INSTRUCTIONS

(IPI)

TO TURN OFF

GAS TO APPLIANCE

1.

Turn  off  all  electric  power  to  the  appli-

ance if service is to be performed.

2.

Flip ON/OFF switch  to the “OFF” posi-

tion.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING:

  If  you  do  not  follow  these  instructions

exactly,  a  fire  or  explosion  may  result  causing  prop-

erty  damage,  personal  injury  or  loss  of  life.

A.

This appliance is equipped with

an  intermittent pilot ignition (IPI)

device which automatically lights

the burner.  Do not try to light the

burner by hand.

B. BEFORE  LIGHTING,

  smell  all

around  the  appliance  area  for

gas.  Be sure to smell next to the

floor  because  some  gas  is

heavier than air and will settle on

the floor.

WHAT TO DO IF  YOU SMELL GAS

• Do not try to light any appliance.

DO NOT CONNECT 110 VAC

TO THE CONTROL VALVE.

Improper  installation,  adjustment,

alteration,  service  or  maintenance

can cause injury or property dam-

age. Refer to the owner's informa-

tion manual provided with this ap-

pliance.
This appliance needs fresh air for

safe  operation  and  must  be  in-

stalled  so  there  are  provisions  for

adequate  combustion  and  ventila-

tion air.
If not installed, operated, and main-

tained  in  accordance  with  the

manufacturer's  instructions,  this

product  could  expose  you  to  sub-

stances in fuel or fuel combustion

which are known to the State of Cali-

fornia  to  cause  cancer,  birth  de-

fects, or other reproductive harm.
Keep burner and control compart-

ment  clean.  See  installation  and

operating instructions accompany-

ing  appliance.

CAUTION:

Hot  while  in  operation.  Do  not

touch. Keep children, clothing, fur-

niture,  gasoline  and  other  liquids

having flammable vapors away.
Do not operate the appliance with

panel(s) removed, cracked or bro-

ken.  Replacement  of  the  panel(s)

should  be  done  by  a  licensed  or

qualified service person.

• Do not touch any electric switch;

do not use any phone in your build-

ing.

• Immediately call your gas supplier

from  a  neighbor's  phone.  Follow

the  gas  supplier's  instructions.

• If you cannot reach your gas sup-

plier, call the fire department.

C.

Do  not  use  this  appliance  if  any

part has been under water. Imme-

diately call a qualified service tech-

nician to inspect the appliance and

to replace any part of the control

system and any gas control which

has been under water.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and pro-

pane. A conversion kit, as supplied

by the manufacturer, shall be used

to convert this appliance to the al-

ternate fuel.

Also Certified for Installation in

a Bedroom or a Bedsitting Room.

For assistance or additional informa-

tion, consult a qualified installer, ser-

vice agency or the gas supplier.

WARNING:

593-913D

GAS

VALVE

For additional information on operating your Hearth & Home Technologies

fireplace, please refer to www.fireplaces.com.

Содержание 6000CF-OAK-IPI




















































Отзывы: