Heat & Glo SL-350TRS-CE-D Скачать руководство пользователя страница 8

Страница: 8 / 47

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. V • 3/13

Heat & Glo direct flue gas fireplaces are designed to

operate with all combustion air siphoned from outside

of the building and all exhaust gases expelled to the

outside.
The information contained in this

Installers Guide

unless noted otherwise, applies to all models and gas

control systems.
Gas fireplace diagrams, including the dimensions, are

shown in this section.
This gas fireplace and its components are tested and

safe when installed in accordance with this

Installers

Guide

. Report to your dealer any parts damaged in

shipment, particularly the condition of the glass.

not install any unit with damaged, incomplete, or

substitute parts.

The flue system components and trim doors are

shipped in separate packages. The gas logs are

packaged separately and must be field installed.

Read all of the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benefit. Failure to follow these instructions

will void the owner’s warranty and may present

a fire hazard.

The Heat & Glo Fireplace Products, Inc. Warranty

will be voided by, and Heat & Glo Fireplace Products,

Inc. disclaims any responsibility for, the following

actions:
• Installation of any damaged fireplace or flue system

component.

• Modification of the fireplace or direct flue system.
• Installation other than as instructed by Heat & Glo

Fireplace Products, Inc.

• Improper positioning of the gas logs or the glass

door.

• Installation and/or use of any component part not

manufactured and approved by Heat & Glo Fireplace

Products, Inc., not withstanding any independent

testing laboratory or other party approval of such

component part or accessory.

aNy such acTiON may pOssibly cause a fire

haZarD.

Introducing the

Heat & Glo

Gas Fireplaces

Pre-installation

Preparation

Getting

Started

Содержание SL-350TRS-CE-D
















































Результаты поиска

Содержание SL-350TRS-CE-D

Отзывы:

Похожие инструкции для SL-350TRS-CE-D

Бренды по названию

Популярные бренды

Heat & Glo SL-350TRS-CE-D, Руководство по установке

Результаты поиска

Содержание SL-350TRS-CE-D

Отзывы:

Похожие инструкции для SL-350TRS-CE-D

Бренды по названию

Популярные бренды