Heat & Glo SL-350TRS-CE-D Скачать руководство пользователя страница 2

Страница: 2 / 47

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. V • 3/13

This appliance is intended for use on a gas installation with a governed meter.

!
!

SAFETY AND wARNING INFORMATION

READ

and

UNDERSTAND

all instructions carefully before starting the installation.

FAILURE

TO fOllOw

these installation instructions may result in a possible fire hazard and will

void the warranty.
Prior to the first firing of the fireplace,

READ

the Using Your Fireplace section of the

Users

Guide

DO NOT use

this appliance if any part has been under water. Immediately

cALL

a qualified

service technician to inspect the unit and to replace any part of the control system and any

gas control which has been under water.

This uNiT is NOT fOr use wiTh sOliD fuel.

Installation and repair should be

perfOrmeD

by a qualified service person. The appliance

and flue system should be

INSpEcTED

before initial use and at least annually by a

professional service person.
Always

kEEp

the appliance clear and free from combustible materials, petrol, and other

flammable vapors and liquids.

Never ObsTrucT

the flow of combustion and ventilation air. Keep the front of the

appliance

cLEAR

of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should be

lOcaTeD

out of traffic areas and

away from furniture and draperies. Clothing or flammable material

shOulD NOT be

pLAcED

on or near the appliance.

Children and adults should be

ALERTED

to the hazards of high surface temperature

and should

STAY AwAY

to avoid burns or clothing ignition. Young children should be

CAREFULLY SUPERvISED

when they are in the same room as the appliance.

These units

musT

use one of the fluing systems described in the Installing the Fireplace

section of the

Installers Guide

NO OTher

flue systems or components

may be useD.

This gas appliance and flue assembly

musT

be vented directly to the outside and

musT

NEvER

be attached to a chimney serving a separate solid fuel burning appliance. Each gas

appliance

musT use

a separate flue system. Common flue systems are

prOhibiTeD

INSpEcT

the external terminal cap on a regular basis to make sure that no debris is

interfering with the air flow.

The glass door assembly

musT

be in place and sealed, and the trim door assembly

musT

be in place on the appliance before the unit can be placed into safe operation.

DO NOT OperaTe

this appliance with the glass door removed, cracked, or broken.

Replacement of the glass door should be performed by a licensed or qualified service

person.

DO NOT

strike or slam the glass door.

The glass door assembly

shall ONly

be replaced as a complete unit, as supplied by the

gas appliance manufacturer.

NO subsTiTuTe

material may be used.

DO NOT use

abrasive cleaners on the glass door assembly.

DO NOT aTTempT

to clean

the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified service

technician perform an appliance check-up at the beginning of each heating season.

Any safety screen or guard removed for servicing must be replaced before operating this

appliance.

Содержание SL-350TRS-CE-D
















































Результаты поиска

Содержание SL-350TRS-CE-D

Отзывы:

Похожие инструкции для SL-350TRS-CE-D

Бренды по названию

Популярные бренды

Heat & Glo SL-350TRS-CE-D, Руководство по установке

Результаты поиска

Содержание SL-350TRS-CE-D

Отзывы:

Похожие инструкции для SL-350TRS-CE-D

Бренды по названию

Популярные бренды