Heat & Glo SL-350TRS-CE-D Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 47

background image

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. V • 3/13

27

Figure 40 Securing vertical Pipe Sections

Figure 41 Securing Horizontal Pipe Sections

H. Securing the Flue Pipe Sections (DVP and

SLP Pipe)

• Vertical runs of DVP pipe must be supported every 2.44

m after the 7.62 m maximum unsupported rise.

•  Vertical runs of SLP pipe must be supported every 2.44 m.
•  Horizontal sections must be supported every 1.52 m.
•  Flue pipe supports or plumbers strap (spaced 120º apart)

may be used to support. See figures 40 and 41.

• Wall shield firestops may be used to provide horizontal

support.

• SLP ceiling firestops have tabs that may be used to

provide vertical support.

warNiNG! risk of fire, explosion or asphyxiation!

Improper support may allow flue pipe to sag and sepa

-

rate. Use flue pipe run supports and connect flue pipe

sections per installation instructions.

DO NOT

allow flue

pipe to sag below connection point to appliance.

«
...
25
26
27
28
29
...
»

Содержание SL-350TRS-CE-D
















































Отзывы:

Нет отзывов

Похожие инструкции для SL-350TRS-CE-D

Бренд: Majestic Страницы: 56

Бренд: Majestic fireplaces Страницы: 56

Бренд: Enviro Страницы: 60

CLAREMONT FA931000TX-CHERRY

Бренд: SEI Страницы: 9

Бренд: PRITY Страницы: 70

Бренд: Travis Industries Страницы: 8

Бренд: Xaralyn Страницы: 15

COMPACT FIREPLACE

Бренд: Dimplex Страницы: 14

Бренд: Paramount Fitness Страницы: 56

Бренд: Ningbo Страницы: 20

Бренд: SimpliFire Страницы: 2

Бренд: Flamerite Fires Страницы: 4

Бренд: Solas Страницы: 35

FP30 Arch Craftsman

Бренд: Pacific energy Страницы: 16

Wellington Surround

Бренд: Valor Fires Страницы: 8

Бренд: Firecraft Страницы: 20

Vittoria GD19P-2

Бренд: Napoleon Страницы: 64

Бренд: Warm Tech Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды