Heat & Glo SL-350TRS-CE-D Скачать руководство пользователя страница 34

Страница: 34 / 47

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. V • 3/13

A tap is provided on the outlet side of the gas control for a

test gauge connection to measure the manifold pressure.

To measure inlet pressure, provisions must be made to

attach a test gauge to the tap immediately upstream of

the gas supply connection to the fireplace.
The fireplace and its individual shut-off valve must be

disconnected from the gas supply piping system during

any pressure testing of the system at test pressures in

excess of 60 mbar.
If the fireplace must be isolated from the gas supply

piping system by closing an individual shut-off valve, it

must be of the handle-less type.

Pressure requirements for Heat & Glo gas

fireplaces are shown in the table below.

Step 7

Gas Pressure

Requirements

Natural Gas

Propane

Butane

Natural Gas

(G20)

(G31)

(G30)

(G25)

Inlet Pressure

20 mbar

30 or 50 mbar 30 or 50 mbar

25 mbar

Manifold Pressure

4 - 8.7 mbar 15.7 - 25 mbar 15.7 - 25 mbar 4 - 8.7 mbar

Gas Rate

.54

.24

.16

.54

Max. Input (NETCV)

6.0 kW

5.4 kW

5.2 kW

5.0 kW

Burner Injector

DMS 44

DMS 55

DMS 56

DMS 42

Pilot Injector

Step 8

wiring the

Fireplace

Optional Accessories

Optional remote control kits require that 230 VAC be

wired to the factory installed junction box before the

fireplace is permanently installed.

wARNING: DO NOT CONNECT 230 vAC

TO THE GAS CONTROL vALvE OR THE

APPLIANCE wILL MALFUNCTION AND THE

vALvE wILL BE DESTROYED

NOTE: Electrical wiring must be installed by a

competent electrician.
Appliance Requirements

• This appliance

DOES NOT

require 230 VAC to

operate.

wall Switch

Position the wall switch in the desired position on a wall.

Run a maximum of 780 cm or less length of 0.102 cm

diameter minimum wire and connect it to the fireplace

ON/OFF switch pigtails.



Содержание SL-350TRS-CE-D
















































Результаты поиска

Содержание SL-350TRS-CE-D

Отзывы:

Похожие инструкции для SL-350TRS-CE-D

Бренды по названию

Популярные бренды

Heat & Glo SL-350TRS-CE-D, Руководство по установке

Результаты поиска

Содержание SL-350TRS-CE-D

Отзывы:

Похожие инструкции для SL-350TRS-CE-D

Бренды по названию

Популярные бренды