Hearth and Home Technologies 350TRSI-AUF Скачать руководство пользователя страница 46

Страница: 46 / 79

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

10" (254 mm)

12" (305 mm)

INTERIOR

WALL SHIELD

G. Install Firestops

For Horizontal Runs -

Firestops are

REQUIRED

on both

sides of a combustible wall through which the fl ue passes.

To install fi restops (heat shield) for horizontal runs that pass
through either interior or exterior walls:

• Cut a 10 inch by 12 inch (254 mm X 305 mm) hole

through the wall.

• Position the fi restops on both sides of the hole previously

cut and secure the fi restops with nails or screws.

• The pipe opening of the fi restops

MUST BE

placed

towards the bottom of the fi restop.

• Continue the fl ue run through the fi restop.

Figure 10.13 Flue Pipe & Firestop

CEILING

NEW
FRAMING
MEMBERS

EXISTING CEILING
JOISTS

CHIMNEY
HOLE

Figure 10.14 Hole and New Framing Members

Figure 10.12 Installing Support Brackets

F. Install Support Brackets

For Horizontal Runs -

The fl ue system must be supported

every fi ve (5) feet (1.52 m) of horizontal run by a horizontal
pipe support. To install support brackets for horizontal runs:

• Place the pipe supports around the fl ue pipe.

• Nail the pipe supports to the framing members.

For Vertical Runs -

The fl ue system must be supported

every eight feet (2.44 m) above the heater fl ue outlet by
wall brackets. To install support brackets for vertical runs:

• Attach wall brackets to the fl ue pipe and secure the wall

bracket to the framing members with nails or screws.

For Vertical Runs -

One fi restop is

REQUIRED

at the hole

in each ceiling through which the fl ue passes.

To install fi restops for vertical runs that pass through
ceilings:

• Position a plumb bob directly over the center of the

vertical fl ue component.

• Mark the ceiling to establish the centerpoint of the fl ue.

• Drill a hole or drive a nail through this center point.

• Check the fl oor above for any obstructions, such as

wiring or plumbing runs.

• Reposition the heater and fl ue system, if necessary, to

accommodate the ceiling joists and/or obstructions.

• Cut a 254 mm X 254 mm hole through the ceiling when

using DVP pipe, and a 229 mm x 229 mm hole when
using SLP pipe. Use the fi restop pipe opening as a
guide.

• Frame the hole with framing lumber the same size as

the ceiling joists.

SLP

229 mm

DVP

254 mm

WALL BRACKET

WALL STUD

2.44 m

FLUE

OUTLET

25 mm

Содержание 350TRSI-AUF
















































































Результаты поиска

Содержание 350TRSI-AUF

Отзывы:

Похожие инструкции для 350TRSI-AUF

Бренды по названию

Популярные бренды

Hearth and Home Technologies 350TRSI-AUF, Руководство пользователя

Результаты поиска

Содержание 350TRSI-AUF

Отзывы:

Похожие инструкции для 350TRSI-AUF

Бренды по названию

Популярные бренды