Hearth and Home Technologies 350TRSI-AUF Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 79

background image

61

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

Frequently Asked Questions/Troubleshooting

Symptom

Possible Cause

Corrective Action

Remote control will not transmit

Batteries

Verify batteries are functional and installed correctly.

Remote control is in Child
Lock mode

Disengage Child Lock mode.

Buttons not being pressed
fi rmly

Press button fi rmly for one to two seconds to ensure transmis-
sion to module.

Control module will not take
commands from remote control

Control module is not in
“REMOTE” mode

Ensure module switch is set to REMOTE.

Control module and remote
control are not programmed
to each other

The control module will beep when it successfully receives a
command. If it does not beep, clear module memory and repro-
gram the remote control.

Control module is un-
plugged. In case of power
outage, backup batteries
are depleted or missing

If  the  transmission  indicator  comes  on  when  power  button  is
pressed, verify that the control module is plugged in the  fi re-
place junction box located in the controls area.  Also verify that
the batteries are installed in the battery pack.

Fan does not turn on when fi replace
is started

Built in time delay

The fi replace must run for seven minutes in order for the fan
to engage.

Fan does not turn off when fi replace
turned off

Built in time delay

The fan will run for twelve minutes after the fi replace is turned off.

Fireplace shuts down after extended
periods

Built-in timer

The fi replace will automatically shut down after nine hours of
continuous operation if it does not receive a command from
the remote.

Fireplace is on but will not shut off
with the remote control

External wired wall switch

The fi replace cannot be turned off by remote if an external
wired switch is installed and in the ON position. Turn external
wall switch to OFF.

Remote control or control
module failure

At control module, turn off fi replace by sliding the ON/OFF/
REMOTE switch to OFF. Warning! Risk of Burns! Fireplace is
hot. Use caution when accessing module.

!

«
...
59
60
61
62
63
...
»

Содержание 350TRSI-AUF
















































































Отзывы:

Нет отзывов

Похожие инструкции для 350TRSI-AUF

Бренд: IHP Страницы: 8

Бренд: Warm House Страницы: 18

LUNA 850 V Gold Gas

Бренд: M Design Страницы: 39

CLASSIC BELL SMALL 3 PF

Бренд: Bellfires Страницы: 88

Бренд: Vanguard Страницы: 32

Бренд: Napoleon Страницы: 20

Бренд: Napoleon Страницы: 128

Бренд: Desa Страницы: 4

Abbotsford 064-4015-0

Бренд: Canvas Страницы: 104

Бренд: Empire Comfort Systems Страницы: 28

Бренд: Faber Страницы: 24

Бренд: RUSTA Страницы: 36

Бренд: Napoleon Страницы: 112

Бренд: Dimplex Страницы: 20

Бренд: JAYLINE Страницы: 16

FireGenie PG121-LPG1

Бренд: Regency Страницы: 44

Бренд: Frigidaire Страницы: 10

Бренд: Frigidaire Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды