Hearth and Home Technologies 350TRSI-AUF Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 79

background image

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

42

Figure 9.17 Fixed Glass Assembly

GLASS

ASSEMBLY

LATCHES

(BOTH BOTTOM

AND TOP)

E. Covers Removal For Servicing

Control Compartment Access Door

• Lift the lower door up and out to access the gas controls.

Trim Door and Glass Door

• Lift the front trim door up and out away from the appliance

side surrounds. Replace the door when servicing is
complete.

• Noting carefully how the brackets fi t on the glass, release

the two spring latches at the top and two at the bottom
of the glass door. Carefully lift the glass up and out away
from the appliance. See Figure 9.17.

Pilot Assembly/Ignition System

• Remove the log set, log grate and burner assembly.

• Disconnect the gas supply tube from the outlet side of

valve.

• Disconnect the orange ignitor wire (I) and white sensor

wire (S) from module.

• Unscrew the pilot assembly bracket and remove, the

pilot assembly along with silicone sealant grommet.

G. Parts Replacement

Fan

• Unplug the fan from the AUX300CE and slide the fan out

the front of the lower controls compartment.

• Fan can be operated at 3 speed levels using RC300AU

remote and AUX300CE. Refer to RC300AU section.

• The fan will automatically turn on after 7 minutes and will

stop 12 minutes after unit has been turned off.

Glass Panel

• To replace the glass door, place the bottom edge into

the lower holders, push glass against unit and secure
the two spring latches at the top and bottom.

H. Adjustments And Replacement Parts

Adjustments  and  replacement  parts  for  this  appliance
should only be done by a qualifi ed service person.  A wir-
ing diagram for the appliance is shown in Section 12.  A
service parts list is shown in Section 16 of this manual.

I. Install Trim and/or Surround

• Install optional trim kits and/or surrounds using the

instructions included with the accessory.

• Use non-combustible materials to cover the gap between

the sheet rock and the appliance (when applicable to the
model).

J. Air Shutter Setting

Figure 9.18

F. Components Removal For Service

• Release the screws at the base of the log grate and

carefully lift up and remove the logs and log grate.

• Remove the base pan.

• Unscrew the brackets at both ends of the burner and

the top two screws locating the pilot bracket (see Figure
9.18). Slide the burner away from the burner orifi ce.

NOTICE:

All screws which were removed must be replaced.

PILOT BRACKET

RETAINING SCREWS

Fixed Glass Assembly

WARNING! Risk of Asphyxiation!

Handle fi xed glass

assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.

•

DO NOT

strike, slam or scratch glass.

•

DO NOT

operate fi replace with glass removed, cracked,

broken or scratched.

•

Replace as a complete assembly.

Removing Fixed Glass Assembly

• Pull the four glass assembly latches out of the groove on

the glass frame. Remove glass door from the appliance
(see Figure 9.17).

Replacing Fixed Glass Assembly

• Replace the glass door on the appliance. Pull out and

latch the four glass assembly latches into the groove on
the glass frame.

Natural Gas

Propane

Butane

350TRSI-AUF

9.5 mm

N/A

N/A

350TRSILP-AUF

N/A

11 mm

12.5 mm

!

!

!

!

«
...
40
41
42
43
44
...
»

Содержание 350TRSI-AUF
















































































Отзывы:

Нет отзывов

Похожие инструкции для 350TRSI-AUF

Бренд: Majestic fireplaces Страницы: 28

Бренд: Majestic fireplaces Страницы: 52

Бренд: Majestic fireplaces Страницы: 4

Бренд: Majestic fireplaces Страницы: 24

Бренд: Majestic Страницы: 64

Royal Collection WMC36

Бренд: Majestic fireplaces Страницы: 8

PerfectView 33LDV

Бренд: Majestic fireplaces Страницы: 4

Бренд: Quadra-Fire Страницы: 40

Antigua PIT1015A

Бренд: Safavieh Furniture Страницы: 3

Бренд: Procom Страницы: 16

purview 42 Series

Бренд: Napoleon Страницы: 128

Бренд: Amantii Страницы: 18

attika 600 MAX-1

Бренд: RAIS Страницы: 26

Бренд: Valor Страницы: 12

Бренд: Vermont Castings Страницы: 48

Бренд: Enviro Страницы: 60

Бренд: Heat&Glo Страницы: 49

Бренд: Bluegrass Living Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды