Hearth and Home Technologies 350TRSI-AUF Скачать руководство пользователя страница 38

Страница: 38 / 79

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT

allow loose materials or

insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.

An attic shield constructed of 26 gauge minimum metal that
extends at least 2 in. (5,1 cm) above insulation is required.

Attic shields must meet specifi ed clearance and be se-
cured in place.

Flat Ceiling Installation

• Remove one shield from box.

NOTICE:

Cut previously installed batt insulation to make

room for the attic insulation shield.

• Wrap shield around pipe if pipe is already installed in

area to be insulated.

• Match the three holes in each side and fasten with three

screws to form a tube.

• Bend three tabs on the bottom of the shield outward to

allow attachment to the ceiling fi restop.

• Bend the remaining bottom tabs inward 90º to maintain

the air space between the pipe and the shield. Set the
shield on the ceiling fi restop and attach to the fi restop.

• Bend all tabs inward 90º around the top of the shield.

These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.

Figure 8.5 Attic Insulation Shield

Figure 8.6 Heat Zone Knockout

E. Installing the Optional Heat-Zone-240V Kit

• Remove the knockout from the fi replace and discard it

(see Figure 8.6).

• Center the duct collar around the exposed hole and

attach it to the fi replace with 3 screws. Note: Do this
BEFORE fi nal positioning of fi replace.

• Determine the location for the air register/fan housing

assembly.

Reference the Heat-Zone-240V Kit instructions for the
remaining installation steps.

Vaulted Ceiling Installation

• Remove one shield from box.

NOTICE:

Cut previously installed batt insulation to make

room for the attic insulation shield.

• Cut the attic insulation shield (if application is for vaulted

ceiling) to fi t your ceiling pitch. Snip cut edge to recreate
1 in. bend tabs all the way around the bottom.

• Wrap shield around pipe if pipe is already installed in

area to be insulated.

• Match the three holes in each side and fasten with three

screws to form a tube.

• Bend three tabs on the bottom of the shield outward to

allow attachment to the ceiling fi restop.

• Bend the remaining bottom tabs inward 90º to maintain

the air space between the pipe and the shield. Set the
shield on the ceiling fi restop and attach to the fi restop.

• Bend all tabs inward 90º around the top of the shield.

These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.

BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE

INSERT 3
SCREWS

BEND 3 TABS
OUTWARD TO
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
CLEARANCE

HEAT-ZONE-GAS
ATTACHES HERE

Содержание 350TRSI-AUF
















































































Результаты поиска

Содержание 350TRSI-AUF

Отзывы:

Похожие инструкции для 350TRSI-AUF

Бренды по названию

Популярные бренды

Hearth and Home Technologies 350TRSI-AUF, Руководство пользователя

Результаты поиска

Содержание 350TRSI-AUF

Отзывы:

Похожие инструкции для 350TRSI-AUF

Бренды по названию

Популярные бренды