Hearth and Home Technologies 350TRSI-AUF Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 79

background image

29

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

Figure 7.9 Flue Components and Terminations

MODEL

350TRSI-AUF

350TRSILP-AUF

FLUE TERMINATION APPROVALS

DVP-TRAP2 HORIZONTAL TERMINATION CAP

DVP-FBHT HORIZONTAL TERMINATION CAP

DVP-TVHW VERTICAL TERMINATION CAP

Flue System Approvals And Installations

These models have fl ue starting collars on both the top
and the back of the unit. Depending upon the installation,
decide which ONE set of starting collars will be used to at-
tach the fl ue system. The starting collar sealing cap must
remain on the starting collar NOT used.

These models use DVP and SLP series direct fl ue com-
ponents when using the TOP fl ue collars and DVP-series
direct fl ue components when using the REAR fl ue collars.

Approved fl ue system components are labeled for identi-
fi cation.

NO OTHER FLUEING SYSTEMS OR COMPO-

NENTS MAY BE USED

. Detailed installation instructions

are included with each fl ue termination kit and should be
used in conjunction with this

manual

. Figure 7.9 shows

fl ue system components and terminations.

Identifying Flue Components

The fl ue systems installed on this gas heater may include
one, two, or three 90° elbow assemblies. The relationships
of vertical rise to horizontal run in fl ue confi gurations using
90° elbows

MUST BE

strictly adhered to. The rise to run

relationships are shown in the fl ueing drawings and tables
on the next few pages.

WARNING! Risk of Fire!

This gas appliance and fl ue as-

sembly must fl ue directly to the outside and must never
be attached to a chimney serving a separate solid fuel
burning appliance. Each gas appliance must use a sepa-
rate fl ue system-common fl ue systems are prohibited.

WARNING! Risk of Fire!

DO NOT apply combustible

materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specifi ed in
this manual. Overlapping material could ignite and will in-
terfere with proper operation of doors and louvers.

• Horizontal sections 3 inches (762 mm) from the top of

the pipe.

• Horizontal sections 2-1/2 inches (635 mm) at wall

shield fi restops.

• Horizontal sections 1 inches (254 mm) from sides and

bottom of the pipe.

• Vertical sections 1 inches (254 mm) on all sides of pipe.

Failure to keep insulation or other material away from vent
pipe may cause over heating and fi re.

For alternative installations, other than depicted, contact
your dealer for further information.

HORIZONTAL

TERMINATION

WALL FIRESTOP

90 DEGREE
ELBOW

VERTICAL
TERMINATION

STORM COLLAR

ROOF FLASHING

HORIZONTAL PIPE
SUPPORT

PIPE LENGTH

WALL BRACKET

CEILING
FIRESTOP

DVP-SERIES

SLP-TVHW

SLP-TRAP2

SLP SERIES

DVP-TRAP2

DVP-TVHW

Flue system termination kits

DVP-FBHT

!

«
...
27
28
29
30
31
...
»

Содержание 350TRSI-AUF
















































































Отзывы:

Нет отзывов

Похожие инструкции для 350TRSI-AUF

Бренд: baltur Страницы: 64

CLASSIC BELL SMALL 3 PF

Бренд: Bellfires Страницы: 88

Бренд: OVE Страницы: 16

e-MatriX 800-500 ST LL

Бренд: Faber Страницы: 24

Бренд: Ravelli Страницы: 9

Brookhaven 20DVT

Бренд: Vermont Castings Страницы: 32

Бренд: Valor Страницы: 10

Бренд: Lamborghini Caloreclima Страницы: 60

Бренд: Lennox Страницы: 28

Fire Ribbon Direct VEnt Slim 26"

Бренд: Spark Страницы: 48

Бренд: EcoSmart Fire Страницы: 12

Бренд: Robinson Willey Страницы: 27

Бренд: Heat & Glo Страницы: 49

PARAGON FOCUS 18 HE

Бренд: Charlton & Jenrick Страницы: 32

Бренд: LG Страницы: 24

Бренд: kozy heat Страницы: 29

Бренд: kozy heat Страницы: 51

Бренд: kozy heat Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды