Hearth and Home Technologies 350TRSI-AUF Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 79

background image

67

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

15

Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualifi ed service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualifi ed service technician. Contact
your dealer to arrange a service call by a qualifi ed service technician.

A. IntelliFire Plus™ Ignition System

Symptom

Possible Cause

Corrective Action

1. Pilot won’t light.

The ignitor/module
makes noise, but no
spark.

A. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.

B. Loose connections or electrical

shorts in the wiring.

Verify no loose connections or electrical shorts in wiring from mod-
ule to pilot assembly. Verify connections underneath pilot assembly
are tight; also verify igniter and fl ame sense wires are not grounding
out to metal chassis, pilot burner, pilot enclosure, mesh screen if
present, or any other metal object.

C. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).

2. Pilot won’t light,

there is no noise or
spark.

A. No power, transformer installed

incorrectly, or depleted batteries.

Verify that transformer is installed and plugged into module. Check
voltage  of  transformer  at  connection  to  module. Acceptable  read-
ings of a good transformer are between 6.4 and 6.6 volts AC.  Bat-
tery  power  supply  voltage  must  be  at  least  4  volts.    If  less  than  4
volts, replace batteries.

B. A shorted or loose connection in

wiring confi guration or wiring har-
ness.

Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fi t. Verify pilot assembly wiring to module. Re-
move and verify continuity of each wire in wiring harness. Replace
any damaged components.

C. Improper wall switch wiring.

Verify that 220/240 VAC power is “ON” to junction box.

D. Module not grounded.

Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.

3. Pilot sparks, but

Pilot will not light.

A. Gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits.

B. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).

C. Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

D. Pilot valve solenoid.

Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.
If below 1.5 volts, replace module. If 1.5 volts or greater, replace
valve.

«
...
65
66
67
68
69
...
»

Содержание 350TRSI-AUF
















































































Отзывы:

Нет отзывов

Похожие инструкции для 350TRSI-AUF

Бренд: LAMBORGHINI Страницы: 40

Бренд: Duraflame Страницы: 8

Бренд: PRITY Страницы: 70

Бренд: Empire Comfort Systems Страницы: 60

(V)KC42NE SERIE

Бренд: Desa Страницы: 40

ChimneyFree 25MM5326

Бренд: Twin-Star International Страницы: 24

Black Beauty Radiant 340

Бренд: Valor Страницы: 9

Бренд: Valor Страницы: 60

Zermatt 10033051

Бренд: Klarstein Страницы: 44

NADIA 14/P/BS/G

Бренд: Kratki Страницы: 32

Бренд: Royal Страницы: 33

Бренд: Charlton & Jenrick Страницы: 32

INFINITY 480 BF

Бренд: Charlton & Jenrick Страницы: 41

Бренд: COUNTRY FLAME TECHNOLOGIES Страницы: 10

Бренд: Laminvale Страницы: 9

Бренд: Travis Industries Страницы: 64

Бренд: Chesney's Страницы: 34

Бренд: Nibe Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды