manualshive.com logo in svg

Hearth and Home Technologies 350TRSI-AUF, Руководство пользователя

Владельцы печи "Hearth and Home Technologies 350TRSI-AUF" могут бесплатно загрузить руководство по эксплуатации на нашем сайте. Это подробное руководство поможет вам правильно использовать вашу печь и поддерживать домашний комфорт. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

59

Heat & Glo  •  350TRSI-AUF, 350TRSILP-AUF  •  2089-980 Rev. C  •  10/10

About ON Mode

•  All functions can be accessed when the remote control 

is in the ON mode.

•  Only active functions will be displayed when the remote 

control is in the ON mode.  For example: if the fan is the 
only function that’s active, the fan icon and fl ame will be 
the only icon shown in the display.

About OFF Mode

Only the following functions can be accessed in the OFF 
mode:

•  AUX1

•  AUX2

Only active functions will be displayed when the remote 
control is in the OFF mode.

Turning ON the Fireplace

•  Press and hold the POWER button for 5 seconds to unlock 

remote, back light will illuminate.  Press the POWER button 
again to turn the fi replace ON.  The fi replace will fi rst ignite 
the pilot.  The main burner will be lit, once the pilot fl ame 
has been established.  The remote will be locked again 
when the fi replace is turned OFF.

NOTICE:

Whenever the fi replace is cycled from OFF to 

ON, the main burner will light on high for 10 seconds before 
returning to the previous user setting.

Adjusting Flame Height

•  Press the 

MENU

 button to activate the menu.

•  Using the 

UP

 and 

DOWN

 arrows highlight the 

FLAME

icon and press 

SELECT

.

•  Use  the 

UP

  and 

DOWN

  arrows  to  adjust  the 

FLAME

HEIGHT

,  then  press 

SELECT

.   The 

FLAME  HEIGHT

can be adjusted to 5 different settings.

NOTICE:

FLAME HEIGHT will not be adjustable for fi rst 

ten seconds when fi replace is turned on.  

NOTICE:

The system will remember the previous FLAME 

HEIGHT  setting  and  will  automatically  adjust  after  10 
seconds.

Adjusting Fan Speed

•  Press the 

MENU

 button to activate the menu.

•  Using the 

UP

 and 

DOWN

 arrows highlight the 

FAN

 icon 

and press 

SELECT

.

•  Use  the 

UP

  and 

DOWN

  arrows  to  adjust  the 

FAN 

SPEED

, then press 

SELECT

. The 

FAN SPEED

 can be 

adjusted to 3 different settings: HIGH, MEDIUM, LOW.

NOTICE:

The fan has a timer built into the control module. 

After  the  fi replace  is  turned  ON  the  timer  will  wait  for  7 
minutes  before  turning  on  the  fan.    In  addition,  the  fan 
will remain on for 12 minutes after the fi replace has been 
turned OFF.    

NOTICE:

Whenever the fan is turned ON, the FAN will start 

up on the high setting for 10 seconds before adjusting to 
the previous user setting.

AUX1 Function (Unit dependent Function)

•  Press the 

MENU

 button to activate the menu.

•  Using the 

UP

 and 

DOWN

 arrows highlight the 

AUX1

 icon 

and press 

SELECT

.

•  Use the 

UP

 and 

DOWN

 arrows to adjust the 

AUX1

output, 

then press 

SELECT

. The 

AUX1

function can be adjusted 

to 4 different settings: HI, MED, LOW and OFF.

AUX2 Function (Unit dependent Function)

•  Press the 

MENU

 button to activate the menu.

•  Using the 

UP

 and 

DOWN

 arrows highlight the 

AUX2

 icon 

and press 

SELECT

.

•  Use the 

UP

 and 

DOWN

 arrows to turn the 

AUX2 ON

 or 

OFF

, then press 

SELECT

.  The 

AUX2

function can be 

either be turned 

ON

 or 

OFF

.

NOTICE:

When the fi replace is turned OFF both AUX1 and 

AUX2 will be turned off.  The AUX1 and AUX2 functions can 
be activated from the remote’s OFF mode, when the fl ame 
is  off.  When  the  fi replace  is  turned  back  ON,  the AUX1 
and AUX2 settings will be restored to the previous setting.

!

Содержание 350TRSI-AUF
















































































Отзывы:

Нет отзывов

Похожие инструкции для 350TRSI-AUF

HAMPTON BAY 100 Use And Care Manual preview
100
Бренд: HAMPTON BAY Страницы: 18
M Design LUNA 700H Instructions For Installation And Use Manual preview
LUNA 700H
Бренд: M Design Страницы: 44
barbas BOX 20 52 Installation And Maintenance Manual preview
BOX 20 52
Бренд: barbas Страницы: 36
HAMPTON BAY TIPTON OFW832S Use And Care Manual preview
TIPTON OFW832S
Бренд: HAMPTON BAY Страницы: 16
Stonegate FP10-27-11-50-OLOAKS Assembly And Operation Manual preview
FP10-27-11-50-OLOAKS
Бренд: Stonegate Страницы: 13
Napoleon SLF Installation Instructions preview
SLF
Бренд: Napoleon Страницы: 2
UBERHAUS DESIGN 83035028 Operator'S Manual preview
83035028
Бренд: UBERHAUS DESIGN Страницы: 13
Napoleon B42NTRE Installation And Operating Instructions Manual preview
B42NTRE
Бренд: Napoleon Страницы: 144
Duraflame DFI-550-22 Manual preview
DFI-550-22
Бренд: Duraflame Страницы: 22
Early Settler Prescott White Mantel Assembly Instructions preview
Prescott White Mantel
Бренд: Early Settler Страницы: 4
Majestic G2000adi Installation And Operation Instructions Manual preview
G2000adi
Бренд: Majestic Страницы: 24
barbas Falcon 73 Installation And Maintenance Manual preview
Falcon 73
Бренд: barbas Страницы: 40
Majestic B36LA Installation, Operation And Maintenance Instructions preview
B36LA
Бренд: Majestic Страницы: 36
Garden Treasures 0062548 Manual preview
0062548
Бренд: Garden Treasures Страницы: 24
Improvements 532761 Owner'S Instruction Manual preview
532761
Бренд: Improvements Страницы: 24
bemodern Pryzm 1000 Instructions For Installation Manual preview
Pryzm 1000
Бренд: bemodern Страницы: 10
Napoleon Oakville Series Installation Manual preview
Oakville Series
Бренд: Napoleon Страницы: 76
glamour BI100 Important Instructions & Operating Manual preview
BI100
Бренд: glamour Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды