background image

 

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 

 

 

1-888-HAY-INDL (1-888-429-4635) 

ISHCP3000FC Rev A 11/30/16

 

Pg. 1 of 16

 

www.haywardflowcontrol.com 

Hayward Flow Control 

 

HAYWARD FLOW CONTROL

 

LifeStar

TM

 MV SERIES AQUATIC PUMP

 

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

 

 
 
 
 
 
 
 
 
 

 

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

TO PREVENT POTENTIAL INJURY, READ THIS MANUAL CAREFULLY AND COMPLETELY.

 

 
 

 

 

 

Basic safety precautions should always be followed, including the following: Failure to follow instructions can cause severe 
injury and/or death. 

 

This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look for one of the 

following signal words and be alert to the potential for personal injury. 

 

WARNING

 

warns about hazards that 

could 

cause serious personal injury, death or major property damage and if 

ignored presents a potential hazard. 

 

CAUTION

 

warns about hazards that 

will 

or 

can 

cause minor or moderate personal injury and/or property damage and if 

ignored presents a potential hazard.  It can also make consumers aware of actions that are unpredictable and unsafe.   

The 

NOTICE 

label indicates special instructions that are important but not related to hazards.

 

Содержание LifeStar MV Series

















Отзывы: